6580
15
Zoom out
Zoom in
Previous page
1/31
Next page
8
ENGLISH
¤6 Input system selector buttons/
FUNCTION SELECTOR buttons (AUDIO/
VIDEO INPUT)
Press one of these buttons once or twice to select a particular source
component. For example, to set the amplifier or receiver to the DVD
input, press the DVD button ¤6 twice within 2 seconds.
Note:
CDR/MD button is set CDR function at initial. To switch MD function,
press and hold down CDR/MD button and press 2 button b.
To return CDR function, press and hold down CDR/MD button and
press 1 button b.
¤7 SOURCE POWER button
Press to switch the power of an individual source component ON or
OFF.
For example, to turn on the DVD player, first press the DVD button ¤6
then press the SOURCE POWER button ¤7.
Note:
All of the MARANTZ components equipped with D-BUS (RC-5)
connection use the same power ON and OFF commands.
As a result, simply pressing the source power button of the remote
control unit also allows you to turn the power of the components
ON and OFF.
LEARNING METHOD
This remote control unit (RC6200SR) can learn, or program in itself,
the remote control code of any function preset under any button of the
remote control unit of any system component, except for the MAIN
POWER and the FUNCTION buttons of the RC6200SR. The functions
of the components that can be controlled through the D-BUS (RC-5)
need not be learned, but the functions of other components must be
learned before they can be controlled from the RC6200SR remote
control unit. To let the RC6200SR learn the remote control code of a
function of a component, follow the learning procedure described
below.
1. Set the mode switch x to LEARN.
2. Select the component with the codes to be learned, by pressing
one of the input selector buttons.
For example, when the CD button is pressed, most of the buttons
on the remote control unit get ready to learn the CD control codes.
3. On the RC6200SR, press the button corresponding to the function
to be learned. For example, if the function to be learned is
playback, press the PLAY ( ) button on the remote control unit.
The LEARN indicator will light up.
4. Place the remote control unit of the component with the function to
be learned at a distance of about 20 cm (8 inches) from the
RC6200SR, so that the head (transmitting side) of the former
remote control unit points the head of the RC6200SR.
5. On the remote control unit of the component, press and hold the
button of the function to be learned, until the learning indicator of
the RC6200SR starts to blink then goes off. The learning
operation is complete when the indicator is extinguished.
6. Set the mode switch to USER.
7. Let the RC6200SR learn other codes by repeating the steps
above for each code.
Note:
When the system mode switch is in the USER position, the buttons
which have not learned any function output the D-BUS (RC-5)
codes when they are pressed. In the RC-5 (D-BUS) position, all
buttons output the D-BUS (RC-5) codes.
FUNCTIONS THAT CAN BE LEARNED
The RC6200SR has buttons that can LEARN to 1, 4 or 10 types of
different codes.
See the chart on the next page for the types of codes that can be
learned by each button.
RECALLING THE PRESET FUNCTION
Even after a button has learned the remote control code of a function,
its originally preset, D-BUS (RC-5) code can be recalled any time by
following the procedure below.
1. Set the mode switch to LEARN.
2. Press the MAIN POWER OFF button and the button which has
learned a function simultaneously.
3. Set the mode switch to USER.
Learning button indications
Although the learning buttons can be used to operate various
components, the indications printed above the buttons are Marantz D-
BUS (RC-5) preset code indications. To make it easier to remember
which buttons perform which operations, therefore, we recommend
that you program operations into buttons having the same or similar
indications.
There are some situations where programming is not possible.
In the following instances, both the TX and LEARN LEDs blink to
indicate that programming cannot be carried out.
1. When the remote control units memory is full.
2. When you attempt to program a command from a remote control
unit using a different signal transmission format.
CLEARING ALL OF THE LEARNED CODES
Use the following procedure to reset all of the buttons which have
learned remote control codes and make them possible to output RC-5
preset codes.
1. Set the mode switch to LEARN.
2. Hold down the MAIN POWER ON and OFF buttons simultaneously for
more than 3 seconds. The TX and LEARN LED will blink and goes off.
3. Set the mode switch to USER.
MAIN POWER
AMP
SOURCE
POWER
TV
AUTO DTS CS5.1
DVD 6.1 DSP
6-STEREO
2CH
VCR1 7CH-DIR
1
ABC
2
DEF
3
GHI
DSS/VCR2
A/D
4
JKL
5
MNO
6
PQR
AUX
S-DIRECT
7
STU
8
VWX
9
YZ_
SURROUND MODES
SLEEP
OFF ON
RC-5/6
USER
LEARN
TX
LEARN
MAIN POWER
AMP
SOURCE
POWER
TV
AUTO DTS CS5.1
DVD 6.1 DSP
6-STEREO
2CH
VCR1 7CH-DIR
1
ABC
2
DEF
3
GHI
DSS/VCR2
A/D
4
JKL
5
MNO
6
PQR
SURROUND MODES
SLEEP
OFF ON
RC-5/6
USER
LEARN
TX
LEARN
POWER
5 cm
Side View
Side View
Top View
Top View
DVD remote
control unit
DVD remote
control unit
DVD remote
control unit
DVD remote
control unit
RC6200SR
RC6200SR
RC6200SR
OK NO GOOD
RC6200SR
15


Need help? Post your question in this forum.

Forumrules
1

Forum

marantz-sr-6200

Reset search

  • Can I Program the bass an treble an volume on each chanel with out the remote control Submitted on 16-4-2021 at 12:47

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-6200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-6200 in the language / languages: English as an attachment in your email.

The manual is 4,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info