6574
25
Zoom out
Zoom in
Previous page
1/36
Next page
22
ENGLISH
MULTI CH. ST
This mode is used to create a wider, deeper and
more natural soundstage from two channel source
material.
This is done by feeding the left channel signal to
both left front and left surround speaker and the
right channel signal to both right front and right
surround speaker. Additionally, the center channel
reproduces a mix of the right and left channel.
CIRCLE SURROUND
II
(CS
II
-CINEMA, CS
II
-MUSIC,
CS
II
-MONO)
Circle Surround is designed to enable multi-
channel surround sound playback of non-encoded
and multi-channel encoded material.
B
ackward compatibility provides listeners with up to
6.1 channels of surround performance from your entire
collection of music and film, including broadcast,
videotape and stereo recorded music.
Depending on source material, you can select CSII-
Cinema mode, CSII -Music mode or CSII-Mono
mode.
Note:
CS II mode is available for 2ch input signals which
are encoded in Dolby Digital or PCM format.
PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32
kHz, 44.1 kHz or 48 kHz.
VIRTUAL
This mode creates a virtualized surround sound
experience from a two-speaker (front L and R)
playback system playing any multi-channel audio
source (such as found on DVDs and digital
broadcasts), including Dolby Digital, Dolby Pro Logic
or DTS.
STEREO
This mode bypasses all surround processing.
In stereo program sources, the left and right channels
play normally when PCM-audio or analog stereo is
input.
With Dolby Digital and DTS sources, the 5.1 multi-
channels are converted to two channel stereo. 96
kHz PCM source material can be played back in
stereo mode.
S (SOURCE ) - DIRECT
In the source direct mode, the tone control circuit
and bass management configuration are bypassed
for full range frequency response and the purist
audio reproduction.
96 kHz PCM source material can be played back in
this mode.
Notes:
Internal speaker size is setup to front L/R = Large,
Center = Large, Surround L/R = Large and
Subwoofer = Yes automatically. Tone controls
and additional processing are also defeated.
When you use this mode with certain DVD and CD
players, performing operations such as Skip or
Stop may momentarily interrupt the output.
CAUTION
NOTE for DTS signal
* Connected DVD-player, laser-disc player or CD-
player needs to support DTS-digital output. You
may not be able to play some DTS source
signals from certain CD players and LD players
even if you connect the player to the SR5400
digitally. This is because the digital signal has
been processed (such as the output level,
sampling frequency, or frequency response)
and the SR5400 cannot recognize the signal as
DTS data.
* Depending on the player used, DTS play may
produce a short noise. This is not a malfunction.
* While signals from DTS-laser disc or CD are
playing in another Surround mode, you cannot
switch to digital input or from digital input to
analog input by INPUT SETUP in SETUP MAIN
MENU or the A/D button.
* The outputs for the VCR 1 OUT, DSS/VCR 2
OUT, TAPE OUT, and CD-R OUT output analog
audio signals. Do not record from CDs or LDs
that support DTS using these outputs. If you do,
the DTS-encoded signal will be recorded as
noise.
NOTE for Dolby Digital Surround EX signal
* When playing Dolby Digital Surround EX-
encoded software in 6.1 channels, it is required
to set the EX/ES mode.
* Note that some of Dolby Digital Surround EX-
encoded software does not contain the
identification signal. In this case, set the EX/ES
mode manually.
NOTE for 96kHz PCM audio
* AUTO, Source- DIRECT, and STEREO modes
can be used when playing PCM signals with a
sampling frequency of 96 kHz (such as from
DVD-Video discs that contain 24 bit, 96 kHz
audio). If such signals are input during playback
in one of the other surround modes, output from
SR5400 will be muted.
* Certain DVD player models inhibit digital output.
For details, refer to the players operation
manual.
* Some DVD formatted discs feature copy
protection. When using such discs, 96 kHz PCM
signal is not outputted from the DVD player. For
details, refer to the player's operation manual.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-5400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-5400 in the language / languages: English as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info