6574
20
Zoom out
Zoom in
Previous page
1/36
Next page
17
ENGLISH
ENGLISH
1 INPUT SETUP (ASSIGNABLE DIGITAL
INPUT)
Four digital inputs can be assigned to a desired
source.
Use this menu to select the digital input jack to be
assigned to the input source.
1.
Select INPUT SETUP in SETUP MAIN MENU
with or cursor button, and press the OK
button.
2.
To select the input source, press or cursor
buttons.
3.
To select the digital input jack , press the or
cursor buttons.
Select Dx-AT for input sources, for automatic
detection of the digital input signal condition.
If there is not a digital signal present, but there
is an analog signal present, the analog signal
will be played.
Select Dig x, when only a digital signal will be
used.
Select ANA for input sources for which no
digital input jacks are used.
4.
After you complete this portion of the set up,
move the cursor to MAIN with or cursor
buttons and press the OK button.
Notes:
The TUNER and AUX are fixed to the analog
input, and cannot be selected for any digital input.
When a DTS-LD or DTS-CD is playing, this setup
is not available. This is to avoid noise being
generated from the analog input.
If Dx-AT is selected and a DVD, compact disc
or LD is fast-forwarded during playback, decoded
signals may produce a skipping sound. In such
cases, change the setting to DIGITAL.
2 SPEAKER SETUP
After you have installed the SR5400, connected all
the components, and determined the speaker
layout, it is now time to perform the settings in the
Speaker Setup menu for the optimum sound
acoustics for your environment and speaker layout.
Before you perform the following settings, it is
important that you first determine the following
characteristics:
2-1 SPEAKERS SIZE
When setting the speaker size in the SPEAKER
SIZE sub-menu, use the guidelines given below.
LARGE:
The complete frequency range for the channel
you are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting
lower than approx. 100 Hz will be output from
the subwoofer.
If the Subwoofer is set to NONE and the front
speakers are set to Large, then the sound will
be output from both the left and right speakers.
1.
Select SPEAKER SETUP in MAIN SETUP
MENU with the or cursor buttons, and press
the OK button.
2.
To select the each speaker , press the or
cursor buttons.
3.
To select the setting of each speaker size,
press the or cursor buttons.
4.
After you complete this portion of the set up,
move the cursor to NEXT with the or
cursor buttons and then press the OK button
to go to the next page.
SUBWOOFER:
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
1INPUTSETUP
CD : D3 - AT TV : ANA
T APE : ANA DVD : D4 - AT
CD-R :D1-AT VCR1 :ANA
DSS : D2 - AT
MA I N E X I T
2-1 SPEAKERS SIZE
SUBWOOFER : YES
FRONT L/R : LARGE
CENTER : SMALL
SURROUND L / R : SMALL
SURR . BACK : SMAL L
LPF /HPF : 100 HZ
BASS M I X : BOTH
MA I N NE X T E X I T
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
If NONE is selected for the Subwoofer setting,
then this setting is fixed to Large.
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are
connected.
LARGE:
Select if the surround left and right speakers are
large.
SMALL:
Select if the surround left and right speakers are
small.
SURR. BACK
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
NONE:
Select if no surround back speaker is connected.
If None is selected for the Surround L/R setting,
then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the
cutoff frequency for the small speakers used. Select
one of the crossover frequency levels according to
the size of the small speaker connected.
80Hz :
Select this when the bass speaker is about 12
cm (4 3/4 inches).
100Hz :
Select this when the bass speaker is about 10
cm (3 15/16 inches).
120Hz :
Select this when the bass speaker is about 8 cm
(3 3/16 inches).
Notes:
Use the above comments as reference when adjusting.
If S- Direct mode , 6.1CH Input is in use, this
function does not take effect.
BASS MIX
The bass mix setting is only valid when LARGE
is set for the front speakers and YES is set for
the subwoofer during stereo playback .
When BOTH is selected, the low frequencies
will be played through the main L&R, as well as
the sub woofer.
In this playback mode, the low frequency range
expand more uniformly through the room, but
depending on the size and shape of the room,
interference may result in a decrease of the
actual volume of the low frequency range.
By selecting MIX, the low frequencies will play
through the main L&R ONLY.
Note:
LFE signals during playback of Dolby Digital or
DTS, will be played through the sub woofer.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-5400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-5400 in the language / languages: English as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info