Manual Marantz SR-5300 (page 26 of 40) (English)

6572

Zoom out

Zoom in

1/40

ENGLISH

BASIC OPERATION

LISTENING TO THE TUNER

MANUAL TUNING

To select the tuner as the source, press the TUNER button t on

the front panel or press the TUNER button c on the remote.

Press the TUNER button t on the front panel or press the

TUNER button c on the remote to select the desired frequency

band if required.

Press the F/P button !5 on the front panel to display the frequency.

Press the TUNING/PRESET or button !4 on the front panel or

press the 1 or ¡ button ⁄2 on the remote.

If FM is selected, press the MODE button !6 on the front panel or

press the MODE button ⁄2 on the remote control to select the

desired audio mode.

(FM) MODE BUTTON OPERATION

When “AUTO” indicator is on in the display, FM stations that

broadcast in stereo will be received in stereo and the “STEREO”

indicator lights.

When “AUTO” indicator is off, all the FM stations will be received in

mono regardless of whether or not they are broadcasting in stereo.

AUTO TUNING (USING THE SR5300)

Press the F/P button !5 on the front panel to display the frequency.

Press the TUNING/PRESET or button !4 on the front panel

for more than 1 second to start the Auto tuning function.

AUTO TUNING (USING THE REMOTE CONTROL UNIT)

Press 1 or ¡ button ⁄2 for more than 1 second to start the Auto

tuning function.

PRESET TUNING

With this unit you can preset up to 30 FM/AM stations in any order. For

each station, you can memorize the frequency and reception mode if

desired.

1-a. Manual Presetting (Using the SR5300)

Refer to the “MANUAL TUNING” or “AUTO TUNING” section

above to tune in a desired station.

Press the MEMORY button !3. “MEMO” indicator starts blinking on

the display.

While “MEMO” is still blinking (approx. 5 seconds), select the

preset number by pressing the TUNING/PRESET or button !4

then press the MEMORY button !3 again.

When a number has been properly input, “MEMO” indicator stops

blinking and goes out.

The station is now stored in the specified preset memory location.

1-b. Manual Presetting (Using the remote control unit)

Tune in a desired station.

Press the MEMO button ⁄6.

Enter the desired preset number with ten keypad ..

Then, press MEMO button ⁄6 again to store.

2. Auto Presetting

This function automatically scans the AM and FM band and enters all

stations with sufficient signal strength into the memory.

Press and hold down the MEMORY button !3 and TUNER button

t simultaneously, auto presetting will start.

“MEMO“ will blink on the display.

Each time the tuner finds a station, the scanning will pause and

memory. Auto presetting will starts.

Operation stops automatically when all 30 preset memory

positions are filled or when auto scanning attains the highest end

of all bands.

To stop the auto preset function at anytime, press the CLEAR

button !2.

3. Recalling a Preset Station

Press the F/P button !5 to change the display to preset.

Select the desired preset station by pressing TUNING/PRESET

or button !4 on the front panel or press CHANNEL button ⁄2 on

the remote.

Note:

• To directly access the preset stations using the numeric keypad,

select the desired preset station by entering one or two digits

using the numeric keypad ..

• To return to the Manual Tuning mode, press the F/P button !5.

4. Preset Scan Tuning (Using the remote control unit)

Press the P.SCAN button ⁄0 on the remote control. (The preset

station with the smallest preset number is recalled first. If no

stations have been preset, “NO PRESET” shows in the display

and the unit returns to the previous mode.)

Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5

seconds each. Preset numbers that do not contain stations are

skipped.

You can fast forward the preset stations by pressing the

CHANNEL ¢ button ⁄2 continuously.

When the desired preset station is received, cancel the preset

scan operation by pressing the CHANNEL 4 button ⁄2 or the

CLEAR button ⁄7.

5. Clearing Preset Stations

You can remove preset stations from memory using the following

procedure.

Recall the preset number to be cleared with the method described

in “Recalling” a preset station .

Press the CLEAR button !2 on the front panel or CLEAR button

⁄7 on the remote control unit for 3 seconds or more.

“CLEAR” appears on the display to indicate that the specified

preset number has been cleared.

6. Frequency Direct Call

Press F.DIRECT button ⁄2 in the TUNER mode on the remote

controller.

Display shows “ FM– – –.––MHz” (at FM mode).

Input your desired frequency with tenkeypad buttons on the

remote controller.

Eg) 98.1 MHz

Press 9, 8, 1 and 0

Display fixed 98.10 MHz and broadcast station received.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-5300 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Marantz SR-5300 Manual

Product: