6552
11
Zoom out
Zoom in
Previous page
1/22
Next page
8
ENGLISH
FUNCTION AND OPERATION
AMP
1, 2, 3
INFO
REMOTE CONTROL CODE SETTING
The remote control unit contains 3 sets of remote
control codes, and it can be used to control up to 3
receivers in one location. To control a second or third
receiver, select the remote control code as explained
below. The selected receiver can be operated from
the remote control.
• When the unit is shipped from the factory, the main
unit and remote control are set to RECEIVER1.
1.
RECEIVER2
To set the remote control to RECEIVER2,
hold down both the AMP button and 2 number
button on the remote control for at least fi ve
seconds.
RECEIVER3
To set the remote control to RECEIVER3,
hold down both the AMP button and 3 number
button on the remote control for at least fi ve
seconds.
2.
Also set the main unit's remote control setting
to the same setting as the remote control.
To
change main unit's remote control setting,
hold down both the AMP and INFO buttons
on the remote control; the remote control
setting (“RECEIVER 1”, “RECEIVER 2” or
“RECEIVER 3”) will be displayed in the display
window on the main unit and main unit setting
will be changed same setting as remote
control.
Notes
To set the remote control back to RECEIVER1, hold
down both the AMP button and 1 number button on
the remote control for at least fi ve seconds.
If the batteries in the remote control are replaced
while the remote control is set to RECEIVER2 or
RECEIVER3, the setting will revert to RECEIVER1.
CONNECTIONS
CONNECTING SPEAKERS
System 2
Right Left
IN
IN
PHONO
ININ OUTIN OUT
DSSAUX
VIDEO
CONTROL
REMOTE
GND
VCR
IN
OUT
L
IN
OUT
INOUT OUT ININ IN
IN
OUTIN IN
(CD-R) (TAPE)
AUXCD DSS PREDVDRECORDER 2 MAINVCRRECORDER 1
IN
R
DVD
AUDIO
R
MONITOR
FLASHER
AC IN
L
R L
MODEL NO. SR4021
MODEL NO. SR4021
SPEAKER SYSTEMS
AM
FM
(
75
)
GND
ANTENNA
SYSTEM
2
SYSTEM
1
SYSTEM 1 : MINIMUM 8 OHMS
SYSTEM 2 : MINIMUM 8 OHMS
UNSWITCHED
1.25A 150W
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
R L
R L
System 1
Right Left
CONNECTING SPEAKER WIRE
1. 2.
3. 4. 5.
3/8inch
(10 mm)
1.
Strip away approx. 3/8inch (10 mm) of wire
insulation.
2.
Twist the bared wire ends tight, to prevent short
circuits.
3.
Loosen the knob by turning it counterclockwise.
4.
Insert the bare part of the wire into the hole in
side of each terminal.
5.
Tighten the knob by turning it clockwise to
secure the wire.
Caution:
• Be sure to use speakers with the specifi ed impedance
as shown on the rear panel of this unit.
To prevent damage to circuitry, do not let the bare
speaker wires touch each other and do not let them
touch any metal part of this unit.
Do not touch the speaker terminals when the power
is on. It may cause you to receive an electric shocks.
Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality
will be corrupted.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SR-4021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SR-4021 in the language / languages: English as an attachment in your email.

The manual is 1,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info