37771
17
Zoom out
Zoom in
Previous page
1/19
Next page
13
ENGLISH
CHANGING THE TEXT BRIGHTNESS ON
THE LCD (LCD CONTRAST ADJUSTMENT)
Changing procedure (Changes can be made from
the main unit when operation is stopped.)
q If playback is in progress, press the
STOP
button to stop playback.
w Hold down the
PAUSE
button on the main unit
for at least two seconds. (This operation does not
work on the remote control.)
After holding down the button for two seconds,
the current contrast value is displayed. Within two
seconds while it is displayed, press the
button to increase the contrast, or press the
button to reduce the contrast. Changes
can be made to the contrast level over the entire
range (+8 to -8).
If the or button is not pressed
within two seconds, the contrast is automatically
set to the currently displayed level.
Display example: Contrast +-0
e Pressing the
STOP
button while changing the
setting returns to the default setting (+-0).
* Any changes made to the LCD contrast setting
are retained even when the power is turned off.
TURNING OFF THE DISPLAY AND
ILLUMINATION (DISPLAY OPERATION)
This function is used to turn the LCD and illumination
lamps (blue) on and off. (Two display statuses are
available.)
1. Mode where LCD and illumination lamp (blue) turn
on
Each time the
DISPLAY
button is pressed during
playback, the LCD and illumination lamp (blue)
switch on and off.
When Display Off is set, the Display Off indicator
(red) lights up.
* When any related button is pressed (such as
when the
OPEN/CLOSE
button,
STOP
button, or button is used), the display is
automatically turned on, but the Display Off
indicator (red) remains lit. If a track is started in
this state, the display is automatically turned off
two seconds later.
* When a track is stopped, the Display Off
indicator (red) and illumination lamp (blue) light
up alternately.
2. Setting for turning on only LCD (illumination lamp
(blue) remains off)
In the default state, the illumination lamp (blue) is
lit. In this state, the illumination lamp (blue)
remains off regardless of whether the LCD is
turned on or off.
Changing procedure (Changes can be made
when operation is stopped.)
q If playback is in progress, press the
STOP
button to stop playback. To make the setting, hold
down the
DISPLAY
button for at least two
seconds from the remote control (RC-11SAS1).
w If the illumination lamp (blue) is lit, it is turned off
and is set off. To change the setting from off to
on, hold down the same operation
DISPLAY
button for at least two seconds to turn on.
* The illumination lamp (blue) off setting is retained
even when the power is turned off, and this setting
remains until the setting is changed to the on
setting.
* The LCD display on/off setting is not retained when
the power is turned off. (This enables you to enjoy
operation each time you use it.)
TIMER PLAY
This unit can perform timer play by cooperating with
your audio timer.
Connect this units power cord to the audio timers
power socket and the timers power cord to power
outlet.
* For connection to audio timer and its operation,
please refer to the instruction manual of your audio
timer.
Setting method of Timer Play
q Press POWER switch to turn ON the power.
w Insert the disc to be played.
* In timer play mode, tracks are played normally.
e Set the audio timer.
Audio Timer
ABOUT BALANCED JACKS
q The balanced output connector uses a XLR
connector.
w The XLR connector for professional use is
internally wired in either of the following two
systems.
1. USA system (Pin w = COLD, Pin e = HOT)
wq
e
GND
HOT
COLD
2.
European system (Pin w = HOT, Pin e = COLD)
wq
e
GND
COLD
HOT
e The SA-11S1 uses the 1. USA system.
When a preamp or main amplifier adopting the
European system is connected using a cable with
XLR balanced connectors, the reproduced signal
may be inverted of phase.
In this case, correct the wiring of the one of the
XLR connectors on the extremities of the cable
to the USA system by exchanging the connections
of pins w and e. This will make it possible to
play the signal with the correct phase.
SA-11S1N(ENG) 04.8.3, 4:42 AMPage 13 Adobe PageMaker 6.5J/PPC
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz SA11S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz SA11S1 in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info