522813
2
Zoom out
Zoom in
Previous page
1/10
Next page
4
English
EE
EE
E
GND (GROUND) TERMINAL
Connect the grounding wire from the turntable to this terminal.
FF
FF
F
TAPE CD-R/MD IN/OUT JACKS
Connect the play (output) jacks and record (input) jacks of tape decks
to these jacks.
Up to three tape decks can be connected.
NOTE:
When a surround processor or graphic equalizer is used, it must be
connected to the TAPE jacks.
GG
GG
G
SPEAKER SYSTEMS
Connect your speaker system to these terminals.
HH
HH
H
REMOTE CONTROL (BUS) TERMINALS
Another item of audio equipment with a remote control (bus) terminal can
be connected to these terminals by using a special-purpose cable. The
bus OUT terminal is used to send signals to another item of equipment.
The bus IN terminal is used to receive signals from another item of
equipment.
II
II
I
POWER CORD
Connect to a household power outlet.
qq
qq
q
POWER SWITCH
Pressing once switches the power ON, and pressing again switches it
OFF. The POWER indicator lights when the POWER switch is ON, and
go out when the POWER switch is OFF.
ww
ww
w
INPUT SELECTOR
Selects the program source to be recorded or played from the PHONO,
CD, TUNER, AUX.
ee
ee
e
VOLUME CONTROL
Adjusts the volume level. Turn the knob clockwise to increase the
volume.
You can also operate the amplifier with a remote control unit.
rr
rr
r
BALANCE CONTROL
Turn the knob to correct an unbalanced program source such as stereo
broadcast or to vary the output level of the left or right channel.
Note that, if the BALANCE control is turned fully in one direction, the
sound will not be heard from the speaker on the other side.
tt
tt
t
TAPE CD-R/MD SWITCHES
Press one of these switches to monitor the playback sound of a tape
deck connected to the rear panel of this unit.
When the CD-R/MD switch is pressed, this unit automatically enters the
tape dubbing mode, the COPY CD-R TAPE indicator lights, and the
playback signal of CD-R or MD can be copied onto tape deck.
Set both of the switches to OFF when the CD-R or MD, tape decks are
not to be played.
For details, refer to "TAPE DECK OPERATION".
yy
yy
y
SOURCE DIRECT SWITCH
When this switch is pressed, the audio signal is supplied directly to the
volume control circuitry (the signal is directed through the minimum
required path to improve the reproduction of high-quality sources).
NOTE:
When this switch is ON, the settings of the tape monitor switches,
and balance control are ignored.
While this switch is depressed, recording, playback, or dubbing of
tapes cannot be carried out even when a tape monitor switch is
pressed.
uu
uu
u
IR SENSOR
The remote sensor receives the infrared commands from the remote
control unit. When an infrared signal is received from the remote control
unit. The remote control unit must always be pointed directly at the
remote sensor.
ii
ii
i
MUTING INDICATOR
Light up when the MUTING button in the remote control unit is pressed.
NOTE:
Be sure to check the VOLUME control setting before pressing this
switch to cancel muting, If the muting is canceled while the volume
setting is high, the speakers could be damaged.
oo
oo
o
PHONES JACK
Insert the standard phone plug of the headphones into this jack.
OPERATION PROCEDURES
TO PLAY AN ANALOG RECORD
1. Set the INPUT SELECTOR switch to PHONO.
2. Play a record on the turntable.
3. Adjust the volume with the VOLUME control.
NOTES:
Set the VOLUME control to the minimum position before placing the
stylus on the record or before replacing the cartridge.
Do not apply shock or vibration to the turntable during play, as this
may cause the stylus to jump and the analog record to be damaged.
If the turntable is installed too close to the speakers, the volume may
not be able to be increased to a high level due to howling.
Do not switch the power OFF while the stylus is on the record surface.
TO LISTEN TO FM/AM BROADCASTS
1. Set the INPUT SELECTOR switch to TUNER.
2. Tune in the desired station on the tuner.
3. Adjust the volume with the VOLUME control.
TO PLAY A COMPACT DISC
1. Set the INPUT SELECTOR switch to CD.
2. Play a CD on the CD player.
3. Adjust the volume with the VOLUME control.
TO PLAY A COMPONENT CONNECTED TO AUX JACKS
The component connected to the AUX jacks on the rear panel can be
played as follows.
1. Set the INPUT SELECTOR switch to AUX.
2. Play the component connected to the selected input.
3. Adjust the volume with the VOLUME control.
TAPE CD-R/MD
SOURCE DIRECT
INTEGRATED AMPLIFIER PM6010OSE
TAPE CD-R/MD
MUTE
MIN MAX
LR
COPY
CD-R>TAPE
CD
PHONO TUNER
AUX
INPUT SELECTOR VOLUME
BALANCE
POWER ON/OFF
PHONES
ON
OFF
ON
OFF
ON
OFF
2 Operate each equipment to start play.
1 3
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz PM6010 OSE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz PM6010 OSE in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info