522814
8
Zoom out
Zoom in
Previous page
1/18
Next page
4
ENGLISH
NAMES AND FUNCTIONS OF PARTS
FRONT PANEL
qwe r ytu
io!0!1!2!3!4
q POWER SWITCH
Pressing once switches the power ON, and
pressing again switches it OFF.
If the POWER switch is in the ON position,
the power of this unit can be turned ON/OFF
by pressing the POWER button on the remote
controller.
w STANDBY INDICATOR
Lights up when the unit is in the standby mode.
e INPUT SELECTOR
Selects the program source to be recorded or
played from the PHONO, CD, TUNER, AUX/
DVD, RECORDER 1 (CD-R), and RECORDER
2 (MD/TAPE).
r SOURCE DIRECT SWITCH
When the switch is not depressed, the audio
signals are applied to the tone and balance
control circuit, enabling the tone and balance
to be adjusted using the knobs.
When the switch is depressed, the audio
signals bypass the tone control circuit and
the balance control circuit. Then, the tone
control knob and the balance control knob
do not function.
t FUNCTION INDICATORS
One of the indicators lights up to indicate
the input source selected with the INPUT
SELECTOR.
y MUTING INDICATOR
Light up when the MUTING button in the remote
controller is pressed.
NOTE:
Be sure to check the VOLUME control
setting before pressing this switch to cancel
muting. If the muting is canceled while the
volume setting is high, the speakers could
be damaged.
u VOLUME CONTROL
Adjusts the volume level. Turn the knob clockwise
to increase the volume.
i LOUDNESS SWITCH
The LOUDNESS switch compensates for
human hearing characteristics by boosting the
bass and treble response at low volume levels
to achieve a more pleasing tonal balance.
o SPEAKERS 1 / 2 SWITCHES
These switches are used to select the speaker
system(s) connected to the SPEAKER SYSTEM
1 / 2 terminals on the rear panel. If both the 1
and 2 switches are pressed to the low positions,
two speaker systems can be used at the same
time.
When headphones are used for listening, set
both switches 1 and 2 to OFF (high positions).
!0 BALANCE CONTROL
Turn the knob to correct an unbalanced program
source such as stereo broadcast or to vary the
output level of the left or right channel. Note
that, if the BALANCE control is turned fully in
one direction, the sound will not be heard from
the speaker on the other side.
!1 BASS AND TREBLE TONE
CONTROLS
Adjusts the tone by controlling the levels of two
frequency bands. Turn each control toward (+)
to enhance the corresponding frequency band,
or toward (–) to attenuate it.
TREBLE: Adjusts the high frequency level.
BASS: Adjusts the low frequency level.
!2 REC SELECTOR SWITCH
Selects the tape dubbing mode between tape
decks or the signal output at the REC OUT
jacks.
!3 REMOTE SENSOR
The remote sensor receives the infrared
commands from the remote controller. When
an infrared signal is received from the remote
controller. The remote controller must always be
pointed directry at the remote sensor.
!4 PHONES JACK
Insert the standard phone plug of the
headphones into this jack.
PM6002N_01_ENG.indd 4PM6002N_01_ENG.indd 4 07.7.18 9:56:13 AM07.7.18 9:56:13 AM
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz PM6002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz PM6002 in the language / languages: English as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info