522817
9
Zoom out
Zoom in
Previous page
1/14
Next page
8
ENGLISH
How to use the remote control unit
1. Remote control unit
The distance between the signal transmitter of the remote control unit
(RC-17mkII PM) and the IR SENSOR of the integrated amplifier (PM-
14mkII) should be less than about 5 meters. To ensure remote control,
the remote control unit should be pointed accurately toward the IR SEN-
SOR and there should be no obstacle between the remote control unit
and the IR SENSOR.
Remote controllable range
Stereo integrated amplifier (PM-14mkII )
Remote control unit (RC-17mkIIPM)
2. Loading batteries
The service life of the batteries used in the remote control unit is about
1 year under normal use.
Remove the batteries when the remote control unit is not to be used for
a long period of time. Replace batteries early whenever they seem to
be weakened.
q Remove the back cover.
w Insert batteries with correct and polarity.
e Slide close the battery cover until it clicks.
Improper use of batteries may cause the risk of fluid leakage or
explosion.
Be specially careful in the following points.
q Insert the batteries with the correct and polarity as indicated
inside the battery case.
w Do not use a brand-new battery and used battery together.
e Dry cell batteries may produce different voltages even when
their shapes are the same. Do not use different types of batter-
ies together.
r Some batteries are rechargeable and some are not. Be sure
to read the caution and instructions described on each bat-
tery.
t Used batteries should be disposed of in compliance with the
treatment method specified for your local area.
R
E
P
E
A
T
P
H
O
N
O
C
D
R
A
N
D
O
M
T
A
P
E
1
L
I
N
E
1
/
T
U
N
E
R
+
/
A
T
A
P
E
2
L
IN
E
2
/T
V
+
/
A
L
I
N
E
3
/
D
V
D
1
2
3
4
5
6
7
8
9
0
O
P
E
N
/
C
L
O
S
E
V
O
L
U
M
E
Approx. 5 m
PRE OUT, MAIN IN TERMINALS
When shipped from the factory, the COUPLED/SEPARATE switch is
set to the COUPLED position. In this condition, the PRE OUT (pre amp
output terminal) and MAIN IN (main amp input terminal) are internally
connected, and can be used as the pre main amp. Therefore, it is not
necessary to insert a short bar in the terminals.
If the COUPLED/SEPARATE switch is set to the SEPARATE position,
the PRE OUT (pre amp output terminal) and MAIN IN (main amp input
terminal) can be used individually.
Connect peripheral equipment such as power amps, channel dividers,
sound effectors, etc to the PRE OUT (pre amp output terminal).
Connect the pre amp to the MAIN IN (main amp input terminal).
The diagram below is an example of connecting a channel divider and
expanding it into a multi amp drive.
IN
IN
PUSH PUSH
GND
LINE
2
LINE
3
LINE
1
RL
CD UNBALANCED
RL
CD BALANCED
RL
CONNECTION 1 GND 2 COLD 3 HOT
SEPARATE
PRE OUT
RL
RL
COUPLED
MAIN IN
OUT
OUT
CD-R
TAPE
SELECTOR
MM
MC
RL
PHONO
+
R
––
L
+
+
R
––
L
+
SPEAKER SYSTEMS
SYSTEM A : 4 16 OHMS
SYSTEM B : 4 16 OHMS
SYSTEM A + B : 8 16 OHMS
AC INLET
HIGH
OUTPUT
L
R
INPUT
L
R
LOW
OUTPUT
SEPARATE
PRE OUT
RL
RL
COUPLED
MAIN IN
R
REMOTE CONTROL
IN
OUT
/TUNER
Other power amplifier
Channel divider
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz PM14 MK2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz PM14 MK2 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info