522817
4
Zoom out
Zoom in
Previous page
1/14
Next page
3
ENGLISH
FOREWORD
This section must be read before any connection is made to the mains
supply.
WARNINGS
Do not expose the equipment to rain or moisture.
Do not remove the cover from the equipment.
Do not push anything inside the equipment through the ventila-
tion holes.
Do not handle the mains lead with wet hands.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to comply with the household
power and safety requirements that exist in your area.
“/02” Version product can be powered by 230 V AC only.
On the rear panel of the “/01” Version product, a voltage selector (2-
position) is provided. Be sure to set the voltage selector to the mains
voltage of your area before using the unit.
IMPORTANT: (For UK version only)
This apparatus is fitted with an approved moulded 13 Amp plug.
To change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI ap-
proved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off
and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a
plug without a fuse is used, the fuse at the distribution board should not
be greater than 5A.
NOTE:
The severed plug must be destroyed to avoid a possible shock hazard
should it be inserted into a 13A socket elsewhere.
HOW TO CONNECT A PLUG
The wires in the mains lead are coloured in accordance with the follow-
ing code:
BLUE—“NEUTRAL” (“N”)
BROWN—“LIVE” (“L”)
1. The BLUE wire must be connected to the terminal which is marked
with the letter “N” or coloured BLACK.
2. The BROWN wire must be connected to the terminal which is marked
with the letter “L or coloured RED.
3. Do not connect either wires to the earth terminal in the plug which
is marked by the letter “E” or by the safety earth symbol or coloured
green or green-and-yellow.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead — not simply over the two wires.
COPYRIGHT
Recording and playback of any material may require consent. For fur-
ther information refer to the following:
Copyright Act 1956
Dramatic and Musical Performers Act 1958
Performers Protection Acts 1963 and 1972
any subsequent statutory enactments and orders
ABOUT THIS USER GUIDE
Refer to the Figures on the page 57 at the rear of this user guide. The
numbers on the diagrams correspond to those in the text. All references
to the connections and controls that are printed in BOLD type are as
they appear on the unit.
PRECAUTIONS
The following precautions should be taken when operating the equip-
ment.
GENERAL PRECAUTIONS
When setting the equipment ensure that:
the ventilation holes are not covered
air is allowed to circulate freely around the equipment
it is on a vibration free-surface
it will not be exposed to interference from an external source
it will not be exposed to excessive heat, cold, moisture or dust
it will not be exposed to direct sunlight
it will not be exposed to electrostatic discharges
Never place heavy objects on the equipment.
If a foreign body or water does enter the equipment, contact your near-
est dealer or service centre.
Do not pull out the plug by pulling on the mains lead, hold the plug.
It is advisable when leaving the house, or during a thunderstorm, to
disconnect the equipment from the mains supply.
CONNECTIONS
(Figure 2)
CONNECTIONS OF TUNER
Connect the output jacks of your stereo tuner to the LINE 1-LINE 3
jaclks of this unit.
CONNECTION OF COMPACT DISC PLAYER
Connect the output jacks of your CD player to the CD jacks of this unit.
CONNECTION OF TURNTABLE
Connect the L (Left) output cord of the turntable to the LPHONE jack
of this unit, and connect the R (Right) output cord to the RPHONE
jack. Also be sure to connect the turntable's grounding wire to the GND
jack of this unit. The GND jack does not have to be connected if the
turntable is not provided with a grounding wire.
CONNECTION OF DCC/TAPE DECK
Connect the IN (recording input) jacks of the tape deck to the OUT
jacks of this unit, and connect the OUT (playback output) jacks of the
tape deck to the IN jacks of this unit.
CONNECTION OF SPEAKER SYSTEMS
This unit is equipped with a sets of SPEAKER SYSTEM terminals.
The speakers in the speaker system should have an impedance be-
tween 4 and 16 ohms. If speakers with an impedance of less than 4
ohms are connected, the protection circuitry may be activated during
play.
Connect the Right channel speaker to the R terminals, and the Left
channel speaker to the L terminals.
The output terminaks have positive (+: Red) and negative (–: Black)
polarity, and each speaker slso has the same polarity (+ and –). When
connecting the speaker, be sure to connect the terminals with the
same polarity (+with +, – with –).
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz PM14 MK2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz PM14 MK2 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info