453869
23
Zoom out
Zoom in
Previous page
1/33
Next page
17
ENGLISH
NAMES AND FUNCTIONSBASIC CONNECTIONSBASIC OPERATIONS
ADVANCED CONNECTIONS
ADVANCED OPERATIONSTROUBLESHOOTINGOTHERS ADVANCED OPERATIONS
ADVANCED OPERATIONS
HOW TO SET ID NUMBERS
If using this unit by itself as a stereo amplifier, set the ID number
to “0” (Default setting is “0”).
Note:
If the ID number is set to a number other than “0”, this unit
cannot be used for standalone operation.
The ID number of the unit appears on the display for about 3
seconds after the power is activated.
When multiple PM-KI-PEARLs are connected, a unique
ID number must be set of each one in order to distinguish
between them.
The unit that centrally controls the other units takes ID 1.
The unit with ID1 is called the “Master”. The other units that
synchronize with the master are called “slaves” and take IDs
“2” ~ “4”.
INPUT SELECTOR Knob DISPLAY button
POWER ON/OFF Switch
Set ID numbers as follows.
1.
While pressing and holding the DISPLAY button, press
the POWER ON/OFF switch.
2.
Turn the INPUT SELECTOR knob to the desired ID
number.
After finishing setting the ID number, turn power to the unit
OFF.
The setting is stored in memory and becomes active the next
time power to the unit is switched ON.
BI-AMP MODE
This unit is equipped with a bi-amp mode to enable a complete
bi-amp connection using two PM-KI-PEARLs. This complete
bi-amp connection is a high-end technique for enhancing
sound quality, proposed by Marantz. Using this system, the
bi-amp supporting speaker system is separated from the
preamplifiers that separately drive the low and high speakers.
(For more information, see STEREO COMPLETE BI-AMP
CONNECTION (page.13).)
STEREO
BI.AMP
The bi-amp mode is engaged by setting the operating mode
switch on the rear panel to “BI-AMP”.
In the bi-amp mode, the signals input to the L channel are sent
to the left and right volume amplifiers from the input selector.
The figures below show example displays in the stereo and
bi-amp modes.
Stereo mode Bi-amp mode
Notes:
Always turn the power to the unit OFF before changing the
operating mode switch setting. Turning the power ON again
activates the new setting.
When in bi-amp mode, the R channel input jacks cannot be
used.
• When in bi-amp mode, the signals input into the L channel
are output from both channels. Therefore, the same signals
are output from the L channel and R channel in RECORDER
OUT, PRE OUT, PHONES OUT.
PM-KI-PEARL_UN_01_Eng.indd 17PM-KI-PEARL_UN_01_Eng.indd 17 09.7.10 11:14:20 AM09.7.10 11:14:20 AM
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz PM-KI-PEARL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz PM-KI-PEARL in the language / languages: English as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantz PM-KI-PEARL

Marantz PM-KI-PEARL User Manual - Dutch - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info