571030

Marantz Model 4270 Manual

19
Zoom out
Zoom in
Previous page
1/24
Next page
Since the calibration is extremely stable and
should
not
have
to
be repeated (except
to
period-
ically check
it),
we
suggest
that
you mark
the
settings
of
your
recorder's
output
level controls
with
a felt-tipped pen. Doing so
will
enable
you
to
easily reset the controls
if
they are
inadvertantly moved.
PROCEDURE FOR RECORD
CALIBRATION
Before proceeding
with
the record calibration,
be certain
that
the playback adjustments have
been performed. DO
NOT
CHANGE TH E POSI-
TIONS OF THE RECORDER'S
PLAYBACK
LEVEL
CONTROLS
(if
any) OR
THE
4270's
PLAY
CAL
CONTROLS.
In
the
event a record calibration is performed by
the use
of
TAPE MOI\IITOR 1 IN and
OUT
Jacks
of
Model 4270,
shift
the SELECTOR switch
to
TAPE 2 after turning on a 400Hz TONE knob.
On the other hand, when the record calibration is
conducted by the use
of
TAPE
MONITOR
2 IN
and
OUT
Jacks,
shift
the SELECTOR switch to
TAPE
1. Home-position the SELECTOR switch
after the calibration.
For Recorders
with
Three Heads
1. Thread a blank tape
onto
your
recorder (or
insert a cassette).
2. Put the 4270's
DOLBY
Switch in the
"PLAY"
position.
3. Put both the 4270's and the recorder's moni-
tor
switches in
the
"Tape"
position.
4. Put the 400Hz TONE Switch in
the
"ON"
(in) position.
5. Commence recording.
6. Adjust the recorder's record level controls
so the tone
will
deflect the 4270's
SIGNAL-
STRENGTH
lVIeter
to
the
"DOLBY
LEVEL"
mark.
For Recorders
with
Two
Heads
1. Thread a blank tape
onto
your
recorder (or
insert a cassette).
2. Put the 4270's
DOLBY
Switch in
the
"OFF"
position.
3. Put the 400Hz TONE Switch in the
"ON"
(in) position.
4. Commence recording.
5. Adjust
the
recorder's record level controls
to
deflect the recorder's meters
to
OVU.
6. Record the tone
for
approximately 15
sec-
onds.
I
7. Stop the recorder and rewind
it
to the begin-
ning
of
the
tone recording.
I
8. Put the 4270's
DOLBY
Switch in the
"PLAY"
position.
I
9. Put the recorder in the play mode and play
back the tape.
10. Note the level reading on the 4270's SIG-
NAL-STRENGTH Meter. To check the left
•
channel level,
put
the METER Switch in the
"OUT"
position. To check the right chan-
nel level,
put
the METER Switch in the
"1
N"
position. The object is
to
adjust the
recorder's record level controls so the play-
back level achieved indicates
"DOLBY-LEV-
EL"
on the 4270's SIGNAL-STRENGTH
Meter.
11.
If
the Meter indicates
"DOLBY
LEVEL"
,
calibration is completed.
12. A)
If
the Meter indication is above the
"DOLBY
LEVEL",
repeat steps 2 - 11,
but
decrease
the record level in step 5
to
slightly below OVU on the recorder's
VU Meters.
B)
If
the Meter indication is below the
"DOLBY
LEVEL",
repeat steps 2 - 11,
but
increase the record level in step 5
to
slightly above OVU on the recorder's
VU Meters.
For all Recorders
After
the
"DOLBY
LEVEL"
has been achieved
on the SIGNAL-STREI\lGTH Meter, DO NOT
change the recorder's
input
or
output
level con-
trols or the 4270's
PLAY
CAL
controls.
Utilizing the recorder's VU Meters, proper Dolby
recording levels are adjustable by using the RE-
CORD
LEVEL
controls on the
front
panel
of
the
4270. This
only
applies when making a Dolby
recording.
Setting the level slightly
lower
than OVU
will
increase the
Dolby
effect.
CHANGING THE RECORDER'S RECORD OR
PLAYBACK
LEVELS
OR
THE
4270's
PLAY
CAL
CONTROLS WI
LL
AFFECT
THE
DOLBY
CALIBRATION
.
15
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz Model 4270 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz Model 4270 in the language / languages: English as an attachment in your email.

The manual is 13,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info