571035
5
Zoom out
Zoom in
Previous page
1/20
Next page
PREPARATION FOR USE
REAR PANEL CONNECTIONS
Figure 1 shows the location of input and output
jacks on the rear panel. These jacks are for "per-
manent" connections. Front panel jacks and their
usewill be discussed later.
All connections to the rear panel should be made
with the power to the entire system turned off.
The rear panel signal connections are arranged in
stereo pairs. All signal connections to the Model
2252, with the exception of the FM antenna and
loudspeakers, should be made with shielded audio
cables. To avoid confusion, connect one cable at
a time between the 2252 and the other compo-
nents of your system. This is the safest way to
avoid cross-connecting channels or confusing
signal sources with destinations.
PHONO INPUTS
The phono jacks are intended for use with mag-
netic phono cartridges and have a 47,000 ohm
input impedance.
If a hum is heard when playing records, this is an
indication that the record player or its connec-
tions are incorrectly grounded. Connect a sepa-
rate ground wire from the turntable or record
changer from to the CHASSIS GROUND binding
post of the Model 2252. If this is ineffective, try
reversing the polarity of the turntable's power
plug.
If hum persists, consult the instruction booklets
for the turntable and/or phono cartridge.
,
~-l
Figure 1. Rear Panel Connection Facilities
TAPE JACKS
TAPE 1 IN
The pair of TAPE 1 IN jacks servetwo purposes:
1. By depressing the TAPE 1 MONITOR push-
switch, signals can be played from a tape re-
corder set for playback mode of operation.
This permits playing the tape source stereo-
phonically or monophonically as indicated by
the position of the MONO pushswitch.
2. While your tape recorder is recording, you can
monitor the resulting tape quality by depress-
ing the TAPE 1 MONITOR pushswitch. This
requires that your recorder be equipped with
separate record and playback heads and sepa-
rate record and playback electronics.
TAPE 2 IN
The signals from your tape recorder connected to
the TAPE 2 IN jacks can be played back when the
SELECTOR switch is placed in the TAPE 2 posi-
tion and the TAPE 1 MONITOR switch is re-
leased. In addition, these jacks allow tape copying
from TAPE 2 to TAPE 1. The resulting recording
can be monitored by depressing the TAPE 1
MONITOR pushswitch.
TAPE 1
& 2 OUT
Connecting these jacks to the line inputs of a
tape recorder permits recording from the program
source indicated by the SELECTOR switch. The
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz Model 2252 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz Model 2252 in the language / languages: English as an attachment in your email.

The manual is 12,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info