Manual Marantz Model 1060 (page 9 of 13) (English)

571043

Zoom out

Zoom in

1/13

,II

boosted at low level listening and this tonal balance

maintained.

MONO IN (L,R) Switch-Depressing both MONO

IN (L,R)

pushswitches will convert all input signals

to the monophonic mode, including signals at the

rear panel TAPE OUT and front panel mic/aux 2

jacks.

'11

While playing a single channel source such as TV or

AM, depress both MONO IN (L,R) pushswitches to

feed the signal through both channels.

When playing a monophonic phonograpn record,

use these pushswitches to suppress rumble, com-

mon mode noise and pinch-effect distortion.

MAIN-SPKR-REMOTESwitch-These switches

select the loudspeaker terminals to which audio

power is fed. Either the MAl N or the REMOTE

pair of loudspeakers may be selected individually,

or both loudspeaker systems may be selected

simultaneously. When both switches are set in

normal OUT position, all loudspeaker terminals are

internally disconnected from the power amplifier

section of the Model 1060. The stereophone jack,

however, is always connected and is not affected

by these switches.

POWER Switch-This switch applies AC power

the Model 1060 and to the SWITCHED conveni-

ence outlets when depressed. When depressed

again, AC power

is removed.

stereophones-'-This jack is internally connected to

the left and right outputs. The sterephones jack is

designed for use with professional stereo head-

phones. Two sets of headphones may be used with

the aid of "Y"

connection. However, it must be

cautioned that a parallel connection of two low

impedance headphones results in a 3 dB loss in

level. A series connection wi II provided more

power for this purpose. Higher impedance phones

may be easily connected

in parallel.

Some Suggestions on Using Tape Recorders with

Your Model 1060

There are several ways to connect and operate tape

recorderswith the Model 1060.To avoidconfusion

in the following discussion, references to "tape

monitoring" assumethe recorder is equippedwith

separate record and playback heads and separate

record and playback preamplifiers. To further

simplify this discussion, a tape recorder usually

connected

to the DIN tape recorder jack or TAPE

IN and OUT jacks on the rear

panel will be referred

to as the "main" recorder; a separate recorder

usually connected

to the rear panel TAPE jacks

will be referred to as the "external"

recorder. This

general arrangement

is shown in Figure 4.

Recording and Playback-The simplest system

involves only one tape recorder, whose line or

"rad io" inputs are connected to the TAPE OUT

jacks on the rear panel of the Model 1060, and

whose playback outputs are connected to the

TAPE IN jacks.

To make a recording, set the selector switch to the

desired program source and set the recorder to

"record." With the TAPE MaN switch in the OUT

position, you can listen to the original program

source. By setting the TAPE MaN

switch to the IN

position, you can listen to (monitor) the "results"

of the recording while it is in progress.

Copying and Editing

Using the input/output and control facilities

of the

Model 1060, and two tape recorders, you can copy

and edit tapes

from one machine to the other. The

general arrangement of the equipment for copying

Figure4.

One Tape Recorder Arrangement for Recording

and Playback

--,-, --,.,

".,-...--

IYIODEli, 1060

"--

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Marantz Model 1060 in the language / languages: English as an attachment in your email.

The manual is 8,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Marantz Model 1060 Manual

Product: