522851
13
Zoom out
Zoom in
Previous page
1/34
Next page
13
ENGLISH
CONFIGURING YOUR REMOTE TO
CONTROL OTHER DEVICES
The TV and Amp devices on the MusicServer remote
control may be individually configured to control a range of
televisions and amplifiers from well known manufacturers.
To configure the remote to control your
television
Press the TV and 5Select buttons simultaneously;
hold them down for 1 second.
The TV button will remain lit for 20 seconds; the
configuration process must be completed during this time.
Enter the 3 digit numeric code matching the
manufacturer of your television from the list in
Appendix A.
Press the TV button again.
The TV button will blink twice to indicate that the
configuration has been accepted. If the TV button does not
blink begin the process again, taking care to enter the
number exactly as printed in the list. If the television is
switched on during the configuration process, entering the
correct code will cause the television to go into standby.
To configure the remote to control your
amplifier.
Press the Amp and 5Select buttons
simultaneously; hold them down for 1 second.
The Amp button will remain lit for 20 seconds; the
configuration process must be completed during this time.
Enter the 3 digit numeric code matching the
manufacturer of your amplifier from the list in
Appendix A.
Press the Amp button again.
The Amp button will blink twice to indicate that the
configuration has been accepted. If the Amp button does
not blink begin the process again, taking care to enter the
number exactly as printed in the list. If the amplifier is
switched on during the configuration process, entering the
correct code will cause the amplifier to go into standby.
Reassigning volume control when using the
MusicServer.
If the volume setting of the MusicServer is set to fixed the
N%Vol. and Mute keys will do nothing (for more information
on volume output settings see the chapter called Advanced
Settings p.X.). These buttons may therefore be configured
to control the volume on your amplifier whilst the HDD
Audio device is selected. To re-configure these keys:
Ensure that the Amp device is correctly configured
to control your amplifier (as shown above).
Press the HDD Audio and 5Select buttons
simultaneously; hold them down for 1 second.
The HDD Audio button will remain lit for 20 seconds; the
configuration process must be completed during this time.
Press the Mute
Press the NVol. + key
Press the Amp device key
The HDD Audio device key will blink twice to indicate that
the configuration has been accepted. If the HDD Audio
button does not blink begin the process again, taking care
to press the buttons in the correct sequence. The NVol.
and Mute keys should now control the amplifier when the
HDD Audio device is selected.
To return the NVol. and Mute keys to their original
configuration repeat the above process, pressing the HDD
Audio button instead of the Amp button.
Note: The HDD Audio button always uses a device
number of 000. You should never need to change this for
normal operation.
CONNECTING YOUR MUSICSERVER
Note: Do not make any connections to the MusicServer
while the power supply is connected and switched on.
Connect the supplied telephone lead to a standard
analogue telephone socket. Connect the other end
of this cable to the socket marked MODEM on the
back panel of the MusicServer.
Connect the red plug of the supplied audio lead to
the red OUT1 socket on the back of the
MusicServer. Connect the adjacent white plug to
the white OUT1 socket on the MusicServer.
Connect the other end of this cable to the AUX or
CD inputs on your amplifier.
Connect the yellow plug of the supplied TV lead to
the yellow VIDEO 1 OUT socket of the
MusicServer. For the European TV lead* connect
the Scart plug to the ext. 1 or 2 socket on the rear
of your TV. For the non-European TV lead connect
the yellow plug to the video input on the rear of your
TV.
Connect the supplied power cord to your mains
power supply.
Switch on your television. Select the appropriate
video channel to view the MusicServer TV User
Interface display.
* For Scart connection, the red and black plugs are not
required.
SWITCHING ON AND OFF
There are two power saving modes available from the
POWER/Standby button on the MusicServer front panel
and the %L button on the remote control.
If you are not using your MusicServer it is strongly
recommended that you place the unit into one of the two
power saving modes.
Standby mode
Standby mode should be used when the MusicServer is
not being used for a short period of time. Putting the unit
into standby takes just a few seconds; switching the unit on
from standby also takes just a few seconds. Do not
remove the power from the MusicServer in this mode.
Off mode
Off mode should be used when the MusicServer is not
being used overnight (or for several days). There is a short
wait whilst the unit is switched to off mode; switching the
unit on from off mode may take a few minutes. When the
unit is in off mode it consumes very little power. You can
safely remove the power from the MusicServer in this
mode.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantz DH9300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantz DH9300 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info