742782
38
Zoom out
Zoom in
Previous page
1/58
Next page
Reference:
- If changes are made in Menus 3 and 4 in Level 1, a new performance check must be carried out
(Section 8.6.)
- The function of the signal light (A7) can be adjusted in level 3, menu 7.
- The function of the lighting (H7) can be adjusted in level 5, menu 4.
i
Advice:
- In case of single wing systems only the intermediate position that was programmed last can be used.
In case of double wing systems no intermediate position can be set.
- If the automatic closing function (Level 3 / Menu 1) is activated, the relay output (Level 1 / Menu 7)
can be reprogrammed if required.
9. Extended operator functions
9.4 Functions overview for the levels
Attention!
After a reset, all the parameters revert to the factory settings.
In order to guarantee the proper operation of the MASTER and SLAVE controls:
- all the required functions must be re-programmed,
- the remote control unit must be re-programmed,
- the MASTER and SLAVE motor units must be driven to the OPEN and CLOSED positions once.
Level 1 – Basic functions
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Menu 3: Intermediate position OPEN (only in case of single wing systems)
Set using the (+ / OPEN) and (- / CLOSE) buttons
“Intermediate position OPEN” – closing function is possible with automatic closing timer
Menu 4: Intermediate position CLOSE (only in case of single wing systems)
Set using the (+ / OPEN) and (- / CLOSE) buttons
Menu 7: Relay output – terminal 16/17 (MASTER only)
A7 B7 C7 D7 E7 F7 G7 H7
Menu 8: RESET (MASTER + SLAVE)
No Yes
Reset
• Reset the SLAVE controls first and complete the controls test.
• Then reset the MASTER controls.
For a different sequence, the control unit must be disconnected from the mains and then switched on again.
38 Operating Instructions, Comfort 580 GB (#91636)
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Control x.51 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Control x.51 in the language / languages: English as an attachment in your email.

The manual is 3,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantec Control x.51

Marantec Control x.51 User Manual - German - 58 pages

Marantec Control x.51 User Manual - German - 58 pages

Marantec Control x.51 User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info