742808
6
Zoom out
Zoom in
Previous page
1/52
Next page
6
EN
4 - PRODUCT INSTALLATION
Before starting the installation, make sure that the product is intact
and that the packaging contains all the components shown.
Make sure that the mounting area is compatible with the overall
dimensions (Fig.1).
Check the allowed use limitation in the diagram in Fig.2
Fig.3 is an example of a typical system:
- Operators (1)
- Photocells (2)
- Posts for photocells (3)
- Flashing light with integrated aerial (4)
- Key or digital switch (5)
Positioning the foundation box and the lever control and blo-
cking system
Depending on the dimensions, dig a suitably sized foundation ditch
(it is recommended to provide adequate drainage in order to avoid
water pooling).
Place the foundation box inside the trench, with the support pivot
aligned with the hinge axis.
Install a conduit for the electrical cables, and another for drainage.
Embed the foundation box in concrete, ensuring it is level and plumb
(Fig.4)
Ensure that the concrete used is prop-erly cured prior to pro-
ceeding with the following steps.
Insert the ball E into the special hole after having greased it.
Insert the control rod A over the foundation box sup-porting pivot B.
Always connect the earth cable to the mains power earth system with a cable minimum cross sectional area of 1.5 mm
2
Fix with a strong welding the wing of the gate on the release lever C,
then put everything on the driving bracket A.
Grease the mechanism using the appropriate grease nipple D
(Fig.4a).
Installing the gear motor
Place the motor reducer gear unit inside the foundation box.
Fix the motor reducer in place inside the foundation box by tighte-
ning the 4 nuts (Fig.5).
Assemble the lever engine (1) on the motor shaft and tighten the
screw (2).
Connect the lever engine (1) command to the bracket (3) through
the lever (4) (Fig.5a).
Connect the motor to the control panel following the instructions in
the manual installation of the card.
Installation of the limit switches in closing
Move the gate in a position fully closed, then adjust and fasten the
screw (Fig. 6).
Installation of the limit switches in opening
Place the gate in the maximum open position, and then then adjust
and fasten the screw (Fig. 6a).
4.2 - Electrical connections
UN24 UN24E
COLOR CABLE RIGHT LEFT RIGHT LEFT
Blue Opening Closing Opening Closing
Brown Closing Opening Closing Opening
Black - - + Encoder
Yellow / Green - - S Encoder
Grey - - - Encoder
In the case of a power failure, the gate can be unblocked mechanically by operating the motor.
Insert the supplied unlocking key and rotate completely the handle (above 90°) (Fig. 8).
To lock back follow the reverse procedure.
4.3 - Emergency unblocking
The automation system must be equipped with a pressure-sen-
sitive edge protecting all possible crushing points (hands, feet,
etc.) in accordance with the requirements of the EN 13241-1
standard.
Your gate shall be equipped with central and side stops, which
are fundamental for the good system operation. (Fig 7).
They shall state that the installer shall check that the tempera-
ture range marked on the drive is suitable for the location.
4.1 - Installation
ATTENTION !
ATTENTION !
ATTENTION !
ATTENTION !
ATTENTION !
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Comfort UN24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Comfort UN24 in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info