Manual Marantec Comfort SU700M (page 5 of 52) (English, German, French, Italian, Polish, Portuguese, Spanish)

742804

Zoom out

Zoom in

1/52

4 - PRODUCT INSTALLATION

4.1 - Installation

Before proceeding with the installation, check the integrity of the

product and that all components are present in the package.

Check that the gate weight respects the limit of the table (paragraph

2.2) and dimensions of the gear motor are met (Fig. 1).

Fig.2 shows a typical installation:

Gear motor (1)

Photocells (2)

Columns for photocells (3)

Flashing light with antenna (4)

Key switch or digital keypad (5)

Pressure-sensitive edge (6)

The automation system must be equipped with a pressure-sen-

sitive edge protecting all possible crushing points (hands, feet,

etc.) in accordance with the requirements of the EN 13241-1

standard.

They shall state that the installer shall check that the tempera-

ture range marked on the drive is suitable for the location.

ATTENTION !

4.2 - Installing the foundation box

Verify the orientation and the overall dimensions of the base plate, x

to ground the base-plate through 4 sturdy screw-anchors or drown it

into the concrete (Fig.3).

Provide one or more corrugated duct tubes for routing the electric

cables.

4.3 - Motor unlock

4.5 - Rack assembling

Open entirely the gate.

Put a rack element on the pinion gear and fasten it to the gate with

screw and spacing bars (Fig.10).

Move the gate manually bringing the pinion gear into line with the

last spacing bar.

Fasten the rack element for good.

4.6 - Limit switch xing

The exact dimensions of the rack must be known to allow pre-

cise calculation of the xing plate position.

With motors with integrated night lights (Night Light System)

make sure not to rip o󰀨 the cable that connects the leds on the

cover with the control board. If necessary, disconnect the con-

nector shown in gure 7.

The stop lock position must assure that the limit switch brackets

don’t collide with the pinion gear. (Fig.11)

For a correct positioning of the other elements and to assure their

straightness, it is necessary to employ a rack element using it as

support and reference. It is besides necessary to assure an aperture

of 2 mm between rack and pinion gear, so that the gate weight doe-

sn’t rest on the gearmotor pinion gear.

The gate has to be equipped with stop locks at the opening and

closing, which prevent the gate derailment.

Haul the gate manually at the opening leaving, depending on the

gate weight, a crack from 30 to 50 mm between the main gate and

mechanical stop.

Fasten the limit switch bracket through the dowels so that the limit

switch is pressed (Fig.11).

Follow the instructions of the control panel and close the cover.

4.4 - Fixing the plate

Open the cover by applying leverage with a screwdriver on the re-

cesses at the sides (Fig.6).

Place the gearmotor on the plate and x the 4 nuts (Fig.8a). If the

permitted adjustment of the rack is not su󰀩cient, before tightening

the nuts the height of the gearmotor can be corrected using the four

regulator stud bolts (Fig.8b).

After the adjustment, it is important to fully tighten the nuts, making

sure that the gearmotor is rmly anchored to the ground throughout

the gate’s travel stroke.

The screws should be tightened again after the gearmotor has been

operated a few times.

Replace the cover so that the light is pointed in the required direction

(Fig.9), such as towards the passage.

To release the gearmotor remove the cap on the side (Fig.4.1) and

turn the pin with the release key or the Sub remote control (Fig.4.2).

Then turn the lever (Fig.5).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Comfort SU700M in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Marantec Comfort SU700M Manual

Product: