742646
26
Zoom out
Zoom in
Previous page
1/44
Next page
26 Manual for installation and operation, Comfort 211 GB (#72752)
Caution!
The automatic cut-out must be
correctly programmed for the CLOSE
and OPEN directions to prevent
damage to persons or property.
8. Initial operation
The operator system determines the maximum required
driving power during the first two runs after setting
the end positions of the door.
• Operate the operator system (with the door coupled)
to drive the door once from the CLOSED position to
the OPEN position and back to the CLOSED position
without interruption.
During this learning run, the operator system
determines the maximum push and pull forces and the
reserve power required to move the door.
1.
After pressing the + button:
The door must open and travel to the
saved OPEN end position.
2.
After pressing the – button:
The door must close and travel to the
saved CLOSED end position.
3.
After pressing the hand transmitter
button: The operator system must move
the door in either the OPEN or CLOSE
direction.
4.
After pressing the hand transmitter
button while the operator system is
running:
The operator system must stop.
5.
When the button is pressed again,
the operator system moves in the
opposite direction.
8.6.2 Check the automatic cut-out function
Check:
After express programming and after
making changes to the programming
menu, the following learning runs and
checks must be carried out.
Automatic cut-out towards CLOSED position
• Place a 50 mm high obstacle on the ground.
• Drive the door towards the obstacle.
The operator system must stop and reverse when
it hits the object.
Automatic cut-out towards OPEN position
If there are openings in the door wing (opening
diameter > 50 mm):
• Place a load weighing 20 kg at the middle of the
lower edge of the door
The door must stop after activating the OPEN
function.
8.6 Function test
8.6.1 Learning run to determine the maximum
required driving power
Advice:
The parameter settings are still saved
if the power supply is disconnected.
Only a reset causes the driving power
settings for the OPEN and CLOSE
directions to revert to the factory
settings.
Test:
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Comfort 211 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Comfort 211 in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantec Comfort 211

Marantec Comfort 211 Usermanual and installation guide - German - 44 pages

Marantec Comfort 211 Usermanual and installation guide - Dutch - 44 pages

Marantec Comfort 211 Usermanual and installation guide - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info