636172
64
Zoom out
Zoom in
Previous page
1/72
Next page
English Page 64
O
25
Test Instructions - only for the specialist -
Trouble shooting:
P
2
1
3
4
5
6
7
8
Fault
Indicator 8 doesn't
glow.
Indicator 6 flashes.
Fault 10
Indicator 6 flashes.
Fault 6 or 15
Drive only operates
in "OPEN" but not
in "CLOSE"
direction.
Fault 15
No response on
impulse.
Indicator 7 glows
No response on
impulse.
Fault 36
Indicator 7 doesn't
flash rapidly on
impulse from hand
transmitter
Insufficient range
of remote control
(less than 5 m).
Indicator 6 flashes.
Fault 9
Cause
No voltage.
Thermal overload protection in motor
activated.
Defective control unit.
Automatic cut-out set too sensitively.
Door movement too sluggish.
Door blocks.
External photocell defective or
interrupted.
Photocell (pt. 21/1) programmed, but
not connected.
Connecting terminals for "IMPULSE"
button bridged, e.g. due to
short-circuit or wrong terminal
connection.
Short-circuit plug removed (pt. 18/T),
but "STOP" button not connected.
Electronic aerial disconnected.
Hand transmitter coding is not
consistent with receiver coding.
Flat battery.
Hand transmitter, control unit
electronics or electronic aerial defective.
Flat battery.
Wrongly positioned electronic aerial.
RPM sensor defective.
Door too sluggish.
Remedy
Check mains supply. Check electric socket.
Check operator mains fuse (pt. 14/L).
Allow motor to cool down.
Cut off mains supply to operator.
Unscrew control unit, pull slightly forward and
withdraw the connecting plug.
Remove control unit and have it checked.
Re-set automatic cut-out to be less sensitive
(pt. 21/3 - "OPEN" direction, pt. 21/4 -
"CLOSE" direction). Ensure door moves easily.
Remove obstruction or have photocell checked.
Reprogramme photocell function or connect
photocell.
Temporarily isolate cabled key switches or
interior push buttons from control unit.
Remove plug (pt. 18/T), insert plug (pt. 18/R)
and look for cable fault.
Connect "STOP" button.
Connect aerial to control unit (pt. 17).
Check coding (pt. 21/6)
Insert new 12V battery A 23 (pt. 15). Flashing
LED in transmitter indicates battery condition.
Have all 3 components checked.
Insert new 12V A 23 battery (pt. 15). Flashing
LED in transmitter indicates battery condition.
Align the aerial cordon and, if possible, let it
hang freely.
Have operator checked.
Check door.
64


Need help? Post your question in this forum.

Forumrules
1

Forum

marantec-comfort-150

Reset search

  • Where can I buy the driving belt between motor and shaft for the garage door

    Submitted on 14-11-2022 at 10:59

    Reply Report abuse
  • when i try to open my door it doesn't open all the way through and sometimes it opens all the way same when closing it
    Submitted on 13-11-2022 at 12:22

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Marantec Comfort 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Marantec Comfort 150 in the language / languages: English, German as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Marantec Comfort 150

Marantec Comfort 150 Usermanual and installation guide - Dutch, French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info