Manual Manitowoc Q210 (page 27 of 40) (English)

603229

Zoom out

Zoom in

1/40

Section 4 Maintenance

Part Number 000001130 12/08 4-5

H. Remove the Bin Door

• Grasp the rear of the bin door and pull bin door

forward approximately 5”.

• Slide bin door to the rear while applying upward

pressure (The rear door pins will ride up into the track

slot and slide backward to the stop tab).

• While applying pressure against the bin door pull

down on the rear of each bin door track until the door

pins clear the stop tabs.

• Slide the rear door pins off the end and then below

the door track. Slide bin door forward allowing the

back of the door to lower into the bin. Continue

forward with the bin door until the front pins bottom

out in the track.

• Lift right side of door until the front pins clear the

track, then remove door from bin.

Step 7 Mix a solution of cleaner and warm water.

Depending on the amount of mineral buildup, a larger

quantity of solution may be required. Use the ratio in the

table below to mix enough solution to thoroughly clean

all parts.

Step 8 Use ½ of the cleaner/water solution to clean all

components. The cleaner solution will foam when it

contacts lime scale and mineral deposits; once the

foaming stops use a soft bristle brush, sponge or cloth

(not a wire brush) to carefully clean the parts. Soak the

parts for 5 minutes (15 – 20 minutes for heavily scaled

parts). Rinse all components with clean water.

Step 9 While components are soaking, use ½ of the

cleaner/water solution to clean all foodzone surfaces of

the ice machine and bin. Use a nylon brush or cloth to

thoroughly clean the following ice machine areas:

• Evaporator plastic parts – including top, bottom and

sides

• Bin bottom, sides and top

Rinse all areas thoroughly with clean water.

Step 10 Mix a solution of sanitizer and warm water.

Step 11 Use 1/2 of the sanitizer/water solution to

sanitize all removed components. Use a cloth or sponge

to liberally apply the solution to all surfaces of the

removed parts or soak the removed parts in the

sanitizer/water solution. Do not rinse parts after

sanitizing.

Step 12 Use 1/2 of the sanitizer/water solution to

sanitize all foodzone surfaces of the ice machine and

bin. Use a cloth or sponge to liberally apply the solution.

When sanitizing, pay particular attention to the following

areas:

• Evaporator plastic parts - including top, bottom and

sides

• Bin bottom, sides and top

Do not rinse the sanitized areas.

Step 13 Replace all removed components.

Step 14 Reapply power and water to the ice machine

and place the toggle switch in the WASH position.

TRACK SLOT

SLIDE DOOR

FORWARD

STOP TAB

PRESS DOWN

TO RELEASE

DOOR

Solution Type Water Mixed with

Cleaner 1 gal. (4 l) 16 oz (500 ml) cleaner

Solution Type Water Mixed With

Sanitizer 6 gal. (23 l) 4 oz (120 ml) sanitizer

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Manitowoc Q210 in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Manitowoc Q210 Manual

Product: