296199
17
Zoom out
Zoom in
Previous page
1/56
Next page
33 34
If you do not operate the camera for 60 seconds, the camera will automatically enter
the sleep mode in order to save battery power. In the sleep mode the camera will not
automatically wind the film to the 1st frame, even if the custom setting is enabled (C-
31 on page 94). In this case, press the shutter release button halfway down to feed
the film to the 1st frame position.
8. Close the back cover.
Push in the upper part of the back cover firmly
to close it.
After attaching the magazine onto the camera
body, pull out the dark slide and press the
shutter button halfway; this will feed the film
automatically to frame No. 1.
Place the dark slide in the magazine's rear
storage pocket.
7. Insert the loaded film insert into
the magazine.
While squeezing the center latches together,
place the film insert, with the feed spool on top,
in the magazine and with pressure on the left
and right blocks push it into proper position.
(You will hear a click).
6. Attach the leader paper of the
film to the empty spool.
As shown in the figure left, gently insert the
leader paper tip into the groove on the empty
spool that is on the “SPL” side, and turn the
spool one or two turns to wrap the leader tape
around it. It is not necessary to finely adjust the
position of the film’s starting edge manually as
the film will be wound into the correct position
automatically.
Turn the spool tight so that the film does not
sag.
When the film is not wound properly, the “- - ” mark appears in the LCD.
Do not wrap too much leader paper around the empty spool. Otherwise the film sec-
tion may be exposed to light.
To prevent accidental film fogging, do not pull out the leader paper too far or load/
unload film under direct sunlight.
Make sure that the film insert is properly fixed. When one or both white latches are
out of position, press the projecting portion or until it clicks.
6-exposure film
If you take more than 8 pictures when using a 6-exposure film, the shutter
blades may be damaged by the leader paper at the film end or by the film tape.
Follow the procedure below.
Photograph in the same way as with 120 film. Eight exposures can be taken.
After taking the 8th exposure, insert the dark slide in the magazine.
Then hold down the emergency film wind button and half-press the shutter re-
lease button.
1. The camera can be set to wind the film to the 1st frame position
automatically after the back cover is closed.
Custom settings (C-32 on page 94)
2. Normally, after the rear cover is closed the shutter cannot be released
without any film in the camera. However, the camera can be set to allow
you to release the shutter without any film.
Custom settings (C-31 on page 94)
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mamiya 645 af d ii at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mamiya 645 af d ii in the language / languages: English as an attachment in your email.

The manual is 3,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info