448701

Makita UT 120 Manual

4
Zoom out
Zoom in
Previous page
1/43
Next page
tzr
Technical Characteristics
Rated voltage: 110 V
Rated power input: 1150 W
Frequency: 50 - 60 Hz
Load speed: 250 - 580 min
-1
Maximum basket diameter: 140 mm
Protection class: II
Degree of protection: IP 20
Collet: M 14
Weight: 4,3 kg
All rights of changes due to technical development reserved.
Safety Instructions
Read and obey these instructions before using this machine.
ADDITIONAL SAFETY RULES FOR THIS MACHINE
1. Disconnect from mains supply whenever any work, servicing and adjustment or change of
accessories and cutters is required.
2. Only grip by insulated part of auxiliary handle and other plastic surfaces when performing drilling
where cutter is likely to contact hidden electrical wiring or its own cable. Contact with a “Live”
wiring will make all exposed metal surfaces of the machine “Live” and danger for an electric shock.
3. Before using the machine, inspect and check power cord and plug for signs of damage and if any
found, have these repaired or replaced immediately. Plug the cord in only after making sure that
mains switch is OFF.
4. Machine should never be damp or wet. Do not use the machine in damp or wet locations.
5. When working this tool always use auxiliary side handle and hold the machine firmly with both
hands. Keep secure stance.
6. For longer machine use, wear hearing protectors.
7. Likewise it is recommended to wear safety helmet, safety glasses and/or face shield. Also wear a
dust mask and thickly padded gloves.
8. Prior to work starting, make sure that cutting accessory is fitted properly.
9. Keep hands well away from rotating parts.
10. Do not leave the machine running unattended. Switch ON only when hand-held.
11. To avoid machine self-starting, always trigger-off the switch should power supply become
interrupted or plug accidentally withdrawn from the socket while motor is still running.
12. When machine is used outdoors, only use extension cords intended and approved for such
application by complying with your local regulations.
13. Always have mains cable routed to the rear and away from the machine and moving parts.
14. Keep sure-footing and body balance at all times for better control of reaction torque.
Protection
Wrong handling can result in damages. Hence, the following instruction should be observed:
Use only Makita paddles with M14 internal thread. Do not allow blocking of the tool due to overload.
Use only original parts from Makita.
Putting into Operation
The operating voltage must correspond with that indicated on identification plate. Mashines designed for 110 V
can be used with 120 V as well.
ENGLISH
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita UT 120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita UT 120 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info