598782

Makita UR3000 Manual

9
Zoom out
Zoom in
Previous page
1/128
Next page
9
8. REFILL OF CUTTING LINE
To refill cutting line:
1. Disconnect the machine from the mains.
2. Remove the empty spool. (Fig. 12 & 13)
3. Cut a new cutting line to less than 8 m and bend it at
the middle.
4. Hook the middle of the new cutting line to the notch
located at the center of the spool between the
2 channels provided for the cutting line. The arrow on
the spool shows the direction of winding the cutting
line. (Fig. 16)
5. Wind the cutting line around the A section (10) in an
orderly placement. Make sure to wind it tight and flat
so that the surface of the wound line is not ragged.
(Fig. 17)
6. Wind all but about 100 mm of the cutting line, leaving
the end temporarily hooked through a line holder (12)
on the side of the spool. (Fig. 18)
7. In this way, wind the cutting line in the B section (11)
as well and leave the end temporarily hooked.
(Fig. 17 & 19)
8. Mount the spool onto the cap so that the temporarily
hooked position of the cutting line (13) matches up
with the notches (14) on the side of the cap (15).
(Fig. 20)
9. Unhook the ends of the cutting line from their
temporary position and fit them into the notches on the
side of the cap. (Fig. 21)
WARNING: Make sure that the cap is secured to
the spool holder properly. Failure to properly secure the
cap may cause the components to fly apart resulting in
serious personal injury.
10. Make sure that the spring is in place. Push the cap
(15) in the spool holder (16). Make sure the latches
fully spread in the cap. (Fig. 14, 15 & 22)
11. Press on the spool button (18) and pull out one end of
the cutting line. Make sure that the line has been fed
out. (Fig. 22 & 23)
12. Finally, pull out the other end of the line without
pressing the spool button. Make sure that the line has
been fed out.
9. FEEDING CUTTING LINE
Short or worn lines cut less efficiently. To improve its
operation on subsequent occasions, tap the spool button
lightly on the ground while the trimmer is running at full
speed. This will automatically feed extra cutting line. The
cutting line blade (17) under the guard will automatically
trim the cutting line to the correct length during operation.
(Fig. 22 & 24)
NOTE: Hitting hard or abrasive objects, such as
fences, concrete and rocks hidden by tall grass may
cause the cutting line to break. If the cutting line breaks,
follow the feeding procedure.
10. INSTRUCTION FOR USE
Start the trimmer before getting close to the grass to be
cut.
Cut the grass by moving the trimmer from right to left and
proceed slowly, keeping trimmer inclined about 30°. High
grass should be cut in layers, always beginning from the
top. The cuts should be short.
Do not cut damp or wet grass.
Avoid wearing the line out quickly by knocking against
hard objects (stone, walls, fences, etc.). Use the edge of
the guard in order to keep the trimmer at the right
distance.
WARNING: Do not use excessive force or hitting
the Trimmer Bump Head on the ground to feed the
trimming line. If the trimming line will not be fed after
tapping the bump head on the ground while the trimmer is
running, the cutting line may have tangled or broken
within the cartridge or the cutting line may have been
used up.
NOTE: Excessive force or hitting the Trimmer Bump Head
on the ground to feed the cutting line will damage the
bump head.
WARNING: The cutting head continues to rotate
after motor is switched off for a few seconds.
11. EXTENSION CORDS
You should only use extension cords for outdoor use,
PVC ordinary duty with a cross sectional area not less
than 0.75 mm
2
.
Before using, check the supply and extension cords for
signs of damaged during use, disconnect the cord for
signs of damage or aging. If the cord becomes damaged
during use, disconnect the cord from the supply
immediately. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use the
appliance if the cord is damaged or worn. Keep extension
cord away from cutting elements.
WARNING: Always ensure that the ventilation
openings are kept clear of debris.
12. MAINTENANCE
1. After use, disconnect the machine from the mains and
check for damage.
2. When not in use, store the machine out of the reach of
children.
3. Mains powered trimmers should only be repaired by
an authorized service center.
4. Ask an authorized service center for any repair of
adjustment other than described in this manual.
5. Use only manufacturer’s recommended replacement
parts and accessories.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita UR3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita UR3000 in the language / languages: All languages as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info