690689

Makita UM603D Manual

15
Zoom out
Zoom in
Previous page
1/100
Next page
15 ENGLISH
3. Adjustthethreepinssothattheyarelinedupon
the alignment line.
►Fig.29: 1.Alignmentline
4. Applyasmallamountofgreasetotheperipheryof
thecrank.Attachthecranktothepinswithitssmalland
largeroundsfacingdown.
►Fig.30: 1. Crank
5.
Slidetheshearbladessothattheholeonthebase
plateispositionedatthecenteroftheringsofblades.
►Fig.31
6.
Turntheshearbladesupsidedownandinstallthemso
thatthepinonthetooltsintheholeontheshearblades.
Inserttheclawofthebaseplateintothegrooveonthetool.
Makesurethattheshearbladesarexedsecurelyinplace.
►Fig.32: 1. Claw
7. Tightenthetwoscrewsrmlywithascrewdriver.
►Fig.33: 1. Screws
8. Placetheundercoversothat
on the under-
cover is aligned with
on the lock lever.
►Fig.34
9. While pressing the undercover, turn the under-
cover clockwise until
on the undercover is aligned
with on the lock lever.
►Fig.35
10. Makesurethatthelocklevertsinthegrooveon
the undercover.
►Fig.36: 1. Lock lever
CAUTION: Never use the tool without install-
ing the undercover.
11. Removethebladecover,andthenturnonthetool
tocheckifthetoolworksproperly.
NOTICE: If the shear blades do not operate prop-
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing the chip
receiver
Optional accessory
CAUTION: When installing or removing the
chip receiver, always wear gloves and attach the
blade cover so that your hands and face do not
directly contact the blade.
Thechipreceivergathersdiscardedleavesandmakes
clean-upafterwardmucheasier.Itcanbeinstalledon
eithersideofthetool.
Toinstallthechipreceiver,pressitagainsttheshearblades
sothatthehookstintotheholesoftheshearblades.
►Fig.37: 1. Hooks 2. Holes
Toremovethechipreceiver,presstheleversonboth
sides to release the hooks.
►Fig.38: 1. Levers
NOTICE: Never try to remove the chip receiver
by an excessive force with its hooks locked in the
holes of the blades.
OPERATION
WARNING:
Before shearing, clear away sticks
and stones from the shearing area. Furthermore, clear
away any weeds from the shearing area in advance.
►Fig.39
WARNING: Keep hands away from blades.
CAUTION: Avoid operating the tool in very
hot weather as much as practicable. When operat-
ing the tool, be careful of your physical condition.
Shearing (for grass shear)
Turnthetoolonafteradjustingtheshearingheightand
holditsothatthebottomofthetoolrestsontheground.
Gentlymovethetoolforward.
►Fig.40
Whentrimmingaroundcurbs,fencesortrees,movethe
toolalongthem.Becarefulthatthebladesdonotcome
into contact with them.
►Fig.41
Whentrimmingsproutsorfoliageofasmalltree,trim
littlebylittle.
►Fig.42
Trimlargebranchestothedesiredheightusingbranch
cuttersbeforeusingthistool.
NOTICE: Do not use the tool in a way that causes
the motor to stop or to rotate extremely slowly.
NOTICE: Do not attempt to cut thick branches.
NOTICE: Do not allow the shear blades to con-
tact the ground during operation. The blades will
be dulled, causing poor performance.
NOTICE: Do not trim the wet grass or foliage of
small trees.
Cutting long lawn
Do not try to cut long grass all at once. Instead, cut the
lawninsteps.Leaveadayortwobetweencutsuntilthe
lawnbecomesevenlyshort.
►Fig.43
NOTE: Cutting long grass to a short length all at once
may cause the grass to die.
Trimming (for hedge trimmer)
CAUTION: Be careful not to accidentally
contact a metal fence or other hard objects while
trimming.Thebladesmaybreakandcauseaninjury.
CAUTION: Be careful not to allow the shear
blades to contact the ground.Thetoolmayrecoil
andcauseaninjury.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita UM603D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita UM603D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 16,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info