Manual Makita UM 164D (page 14 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448698

Zoom out

Zoom in

1/88

• Do not trim wet grass or foliage of small trees.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Shear blade maintenance (Fig. 24 & 25)

After operation, remove dust from both sides of the blade

with wired brush, wipe off it with a rag and then apply

enough low-viscosity oil, such as machine oil etc. and

spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so may

cause rust or damage on the tool.

• Dirt and corrosion cause excessive blade friction and

shorten the operating time per battery charge.

After use

• To clean off the exterior of the tool, dampen a soft cloth

in a soapy water and wipe gently. Never use thinner or

benzine.

• Do not store the tool in a place where volatile materials

are stored.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Grass shear blade assembly

• Grass shear blade cover

• Base frame

• Battery cartridge BL1013

• Battery charger DC10WA

• Long handle attachment

For cordless hedge trimmer use (Fig. 26)

This tool can be used as a hedge trimmer by using the

hedge shear blade (optional accessory) and 2-way

change set (optional accessory).

To use this tool as a hedge trimmer, replacing the grass

shear blades with the hedge shear blades is required.

For removing the grass shear blades, refer to the

aforementioned section titled “Installing or removing grass

shear blades”. For installing the hedge shear blades, refer

to the section below titled “Installing or removing hedge

shear blades”.

• Hedge shear blade assembly (for Hedge Trimmer)

• 2-way change set consisting of the following two

accessories

• Hedge shear blade cover (for Hedge Trimmer)

• Storage case (for blade bottom section)

• Chip receiver for hedge trimming (for Hedge Trimmer)

Installing or removing hedge shear

blades

CAUTION:

• Before installing or removing shear blades, always be

sure that the tool is switched off and the battery

cartridge is removed.

• When replacing the shear blades, always wear gloves

without removing blade cover so that hands and face

do not directly contact the blade. Failure to do so may

cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

• For specific way of removing and installing shear

blades refer to the reverse of a package for accessory

shear blades.

Installing the hedge shear blades (Fig. 27)

Prepare the crank, the undercover and new shear blades.

(Fig. 28)

Adjust the three pin position so that these three pins are

aligned with the basic alignment line on the tool housing.

(Fig. 29)

Fit the crank with its recessed part facing downward onto

the pins. At this time, apply a small amount of grease to

the periphery of the crank using grease that the shear

blades as optional accessory are provided with or that

remains inside gear housing. (Fig. 30)

Overlap the oval hole in the upper blade with that in the

lower one. Move the shear blades so that the hole in the

base plate of shear blades are positioned in the center of

these overlapped oval holes. (Fig. 31)

Take out the blade cover from the old shear blades and fit

it onto the new ones for easy handling during the

replacement of blades. (Fig. 32)

Turn the shear blades upside down and install it so that

pin on the tool fit in the hole in the shear blades. Fit the

bent part of the base plate of the shear blades to the

groove in the tool housing. Then make sure that the base

plate of the shear blades is set in place. (Fig. 33)

Tighten two screws with a coin or similars firmly. (Fig. 34)

Place the undercover so that the symbol on the

undercover is aligned with the symbol on the locking

lever. (Fig. 35)

Press the undercover down and with the undercover

pressed down turn the undercover clockwise until the

symbol on the label is aligned with the symbol on the

locking lever (the undercover is completely locked.).

(Fig. 36)

At this time, make sure that the locking lever fits in the

groove in the undercover.

CAUTION:

• Never use the tool without installing the undercover on

it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita UM 164D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita UM 164D Manual

Product: