Manual Makita UH201D (page 16 of 108) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

690688

Zoom out

Zoom in

1/108

16 ENGLISH

Installing or removing the shear

blades for grass shear

Removing the shear blades

1. Remove the grass receiver and place the tool

upside down.

►Fig.11

2. While pressing the lock lever, turn the undercover

counterclockwise until

on the undercover is aligned

with on the lock lever.

►Fig.12

3. Removetheundercover,shearblades,andcrank.

►Fig.13: 1.Undercover2.Shearblades3. Crank

Installing the shear blades

1. Preparethecrank,undercover,andnewshear

blades.

►Fig.14: 1. Crank 2.Undercover3.Shearblades

2. Removethebladecoverfromtheoldshear

blades,andthenattachittothenewones.

►Fig.15

3. Adjustthethreepinssothattheyarelinedupon

the alignment line.

►Fig.16: 1.Alignmentline

4. Applyasmallamountofgreasetotheperiphery

ofthecrank.Attachthecranktothepinswiththesmall

andlargeroundsfacingup.

►Fig.17: 1. Crank

5. Adjustthebladesandbaseplatesothatthehole

inthebaseplateandthetwoprotrusionsontheblades

are lined up.

►Fig.18

6. Turntheshearbladesupsidedownandinstall

themsothatthepinsonthetooltintheholeonthe

baseplate.Makesurethattheshearbladesarexed

securely in place.

►Fig.19

7. Placetheundercoversothat

on the under-

cover is aligned with on the lock lever.

►Fig.20

8. While pressing the undercover, turn the under-

cover clockwise until

on the undercover is aligned

with on the lock lever.

►Fig.21

9. Makesurethatthelocklevertsinthegrooveon

the undercover.

►Fig.22: 1. Lock lever

CAUTION: Never use the tool without install-

ing the undercover.

10. Removethebladecover,andthenturnonthetool

to check that it works properly.

NOTICE: If the shear blades do not operate prop-

erly, the blades are not engaging the crank prop-

erly. Remove the blades and install them again.

Installing or removing the shear

blades for hedge trimmer

CAUTION: Attach the blade cover before

removing or installing the shear blades.

Removing the shear blades

1. Placethetoolupsidedown.

►Fig.23

2. While pressing the lock lever, turn the undercover

counterclockwise until

on the undercover is aligned

with on the lock lever.

►Fig.24

3. Remove the undercover.

►Fig.25

4. Loosen the two screws with a screwdriver and

removetheshearblades.

►Fig.26: 1. Screws

NOTE:Theshearbladescanberemovedwithout

removing the screws.

5. Removethecrankfromtheshearblades.

►Fig.27: 1. Crank

NOTE:Thecrankmayremaininthetool.

Attachthebladecoverandthestoragecasetothe

removedshearblades,andthenstoretheblades.

Installing the shear blades

1. Preparethecrank,undercover,andnewshear

blades.

►Fig.28: 1. Crank 2.Undercover3.Shearblades

2. Attachthebladecovertotheshearblades.

►Fig.29

3. Adjustthethreepinssothattheyarelinedupon

the alignment line.

►Fig.30: 1.Alignmentline

4. Applyasmallamountofgreasetotheperiphery

ofthecrank.Attachthecranktothepinswiththesmall

andlargeroundsfacingdown.

►Fig.31: 1. Crank

5. Slidetheshearbladessothattheholeonthe

baseplateispositionedatthecenteroftheringsofthe

blades.

►Fig.32

6. Turntheshearbladesupsidedownandinstall

themsothatthepinonthetooltsintheholeonthe

shearblades.Inserttheclawofthebaseplateintothe

grooveonthetool.Makesurethattheshearbladesare

xedsecurelyinplace.

►Fig.33: 1. Claw

7. Tightenthetwoscrewsrmlywithascrewdriver.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita UH201D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 16,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita UH201D Manual

Product: