Manual Makita UC 3530 (page 19 of 136) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian)

78214

Zoom out

Zoom in

1/136

Saw chain oil (Fig. 38)

Use a special oil with adhesive addition for lubricating

the saw chain and bar. The adhesive addition prevents

that the oil is centrifuged too fast from the sawing

device.

Do not use mineral oils. In order to protect the

invironment the use of biologically decomposeable oil is

prescribed.

The saw chain oil sold by MAKITA, called BIOTOP,

is made of special vegetable oils and is biologically

decomposeable to 100%. BIOTOP has been granted

the “blue angel” for being particularly favourable to the

environment (RAL UZ 48).

BIOTOP oil is available in the following packing sizes to

suit your individual requirements:

1 liter order number 980 008 610

5 liters order number 980 008 611

Biologically decomposeable oil is stable only for a

limited period of time. It should be consumed within

2 years from the date of manufacture (printed on the

container). (Fig. 39)

Important note on bio-degradable chain oils

If you are not planning to use the saw again for an

extended period of time, empty the oil tank and put in a

small amount of regular engine oil (SAE 30), and then

run the saw for a time. This is necessary to flush out all

remaining bio-degradable oil from the oil tank, oil-feed

system, chain and guide bar, as many such oils tend

to leave sticky residues over time, which can cause

damage to the oil pump or other parts.

The next time you use the saw, fill the tank with

BIOTOP chain oil again. In case of damage caused by

using waste oil or unappropriate chain oil the product

guarantee will be null and void.

Your salesman will inform you about the use of chain oil.

Never use waste oil (Fig. 40)

Waste oil is very dangerous for the environment.

Waste oil contains high amounts of carcinogenic

substances.

The residues in the waste oil result in a high degree of

wear and tear at the oil pump and the sawing device.

In the case of damage caused by using waste oil or

unappropriate saw chain oil the product guarantee will

be null and void.

Your salesman will inform you about the use of saw

chain oil.

Avoid skin and eye contacts (Fig. 41)

Mineral oil products as well as oil degrease the skin.

If your skin repeatedly comes in contact with these

substances for a longer period of time, it will desiccate.

Various skin deseases may result. In addition, allergic

reactions are known.

Eyes can be irritated by contact with oil. If oil gets into

your eyes, immediately wash them with clear water. If

your eyes are still irrritated, go to see a doctor.

Refilling the oil tank (Fig. 42)

Only if the motor is switched off and the power

supply plug is pulled out!

- Thoroughly clean the oil tank around the cap to

prevent dirt from entering the tank.

- Unscrew the tank cap (1) and fill in chain oil until it is

on a level with the bottom edge of the filler socket.

- Tightly screw on the tank cap.

- Thoroughly remove any oil that has overflown.

Important! (Fig. 43)

Before operating the saw for the first time, the oil feed

system must be completely filled, until the chain oil

lubricates the chain and guide bar.

This procedure can take up to two minutes.

- The oil level can be controlled in the sight glass (2).

In order to ensure sufficient lubrication of the saw chain

there must always be enough oil in the tank.

Lubricating the saw chain (Fig. 44)

Only if the motor is switched off and the power

supply plug is pulled out!

To guarantee a troublefree operation of the oil pump the

oil guide groove (3) as well as the oil inlet bore in the

guide bar (4) must be cleaned in regular intervals.

Note:

After the saw has been turned off it is normal for

residual chain oil to drip from the oil feed system,

the guide bar and the chain for a time. This does not

constitute a defect!

Place the saw on a suitable surface.

Plug in the saw (Fig. 45)

CAREFUL!

Before connecting the saw to a source of

electricity, always make sure to check that when

the ON/OFF switch (1) has been pressed in and

released, it automatically comes back out to the

“off” position. If it does not, do not under any

circumstances connect the saw to a power source

- do not plug it in. Take the saw to a MAKITA

service centre before doing any work with it.

Clip the extension cord and the saw’s power cord into

the cord grip (2).

Plug the saw plug (3) into the socket of the extension

cable (4).

Switching on the motor (Fig. 46)

- Plug in the saw (see above).

- When switching on the electric chain saw always

hold it with both hands. Take the back handle with

the right hand and the tubular handle with the left

hand. Hold the handles tightly with your thumbs facing

your fingers. The bar and chain must not be in contact

with any object.

- First depress the locking button (5) and then the

power switch (1). Then release the locking button (5).

- Attention: The chain starts running immediately.

Keep the power switch depressed as long as the

motor is to run.

CAUTION:

Never lock the power switch in the ON position.

Switching off the motor

- Release the power switch (1).

NOTE:

When the chain brake is actuated the power supply

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita UC 3530 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 5,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita UC 3530 Manual

Product: