Manual Makita TM3010CX2J (page 6 of 14) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711184

Zoom out

Zoom in

1/14

20. Do not use accessories which are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

21. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear hearing

protectors, gloves and workshop apron capable

of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping flying debris generated by various

operations. The dust mask or respirator must be

capable of filtrating particles generated by your

operation. Prolonged exposure to high intensity

noise may cause hearing loss.

22. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of

operation.

23. Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and pull

the power tool out of your control.

24. Do not run the power tool while carrying it at

your side. Accidental contact with the accessory

could snag your clothing, pulling the accessory into

your body.

25. Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

26. Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

27. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

28. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

29. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high

locations.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function

on the tool. Failure to switch off and unplug the tool

may result in serious personal injury from accidental

start-up.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the tool is switched off.

To start the tool, slide the slide switch toward the “I (ON)”

position.

To stop the tool, slide the slide switch toward the “O

(OFF)” position.

Adjusting the orbital stroke rate (Fig. 2)

The orbital stroke rate is adjustable. To change the orbital

stroke rate, turn the dial between 1 and 5. The higher the

number is, the higher the orbital stroke rate is. Preset the

dial to the number suitable for your workpiece.

NOTE:

• The dial cannot be turned directly from 1 to 5 or from 5

to 1. Forcing the dial may damage the tool. When

changing the dial direction, always turn the dial moving

it through each intermediate number.

Constant speed control

Electronic speed control for obtaining constant speed.

Possible to get fine finish, because the orbital stroke rate

is kept constant even under load condition.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing application tool (optional

accessory) (Fig. 3, 4, 5 & 6)

WARNING:

• Do not install application tool upside down. Installing

application tool upside down may damage the tool and

cause serious personal injury.

• Install attachment tool in the correct direction according

to your work. Application tool can be installed at an

angle of every 30 degree.

CAUTION:

• Be careful when closing the lock lever. The lock lever

may close suddenly and pinch your finger.

• Clean up dust and perform lubrication on the moving

part of the lock lever from time to time. Otherwise dust

may accumulate in the moving part of the lock lever

and hinder its smooth movement.

• Do not start the tool while the lever opens. The tool

may be damaged.

1. Open the lock lever fully. And remove the holder

bolt.

2. Put an application tool (optional accessory) on the

tool flange so that the protrusions of the tool flange

fit in the holes in the application tool.

3. Insert the holder bolt till it stops. And then, return the

lock lever to its original position.

When using sanding application tool, mount the

application tool on the sanding pad so that it matches the

sanding pad direction.

The sanding pad has a hook and loop type fitting system

which allows easy and rapid fitting of a sanding paper.

As sanding papers have holes for dust extraction, mount

a sanding paper so that the holes in a sanding paper

match those in the sanding pad.

To remove a sanding paper, raise its end and peel it off.

To remove the holder bolt, follow the installation

procedures in reverse.

When using application tools with a different type of

installation section, use a correct adapter (optional

accessory).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita TM3010CX2J in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita TM3010CX2J Manual

Product: