657961

Makita ST113D Manual

7
Zoom out
Zoom in
Previous page
1/60
Next page
7 ENGLISH
ASSEMBLY
CAUTION: Always make sure that the battery
cartridge is removed before carrying out any work
on the stapler.
Staples
CAUTION: Do not use staples other than
designated in this manual or staples that appear
to be damaged, bent, rusty or corroded.
CAUTION: Load the same type, size and
uniform length of staples when loading multiple
strips of staples in the magazine.
NOTICE: Handle the staples and their box care-
fully. If the staples have been handled roughly,
they may be bent out of shape, causing poor
staple feed or jamming.
NOTICE:
Avoid storing the staples in a very humid
or hot place or place exposed to direct sunlight.
Loading staples
WARNING: When loading staples, always
make sure that the battery cartridge is removed
from the stapler.Unintentionalringmaycause
personalinjuriesandpropertydamage.
CAUTION:
After loading staples, make sure that
the sub magazine is surely closed. Falling staples out
ofthemagazinemaycauseaninjurytotheoperatoror
bystander, especially when working in high locations.
1. Remove the battery cartridge.
2. Pressthelockingleverandslidethesubmaga-
zine backward.
►Fig.6: 1. Locking lever 2. Sub magazine
3. Load staples into the main magazine with their
feetfacingup.
►Fig.7: 1. Staples 2.Mainmagazine
4. Afterloadingstaples,pushbackthesub-maga-
zine in place until it clicks.
Toremovestaples,followtheinstallationproceduresin
reverse.
Hook
CAUTION: Do not hang the hook from the
waist belt. Dropping the stapler, which is caused by
thehookaccidentallycomingoutofplace,maycause
unintentionalringandresultinpersonalinjuries.
►Fig.8
Thehookisconvenientfortemporarilyhangingthetool.
Thiscanbeinstalledoneithersideofthetool.
Toinstallthehook,insertitintoagrooveinthetool
housing on either side and then secure it with a screw.
Toremove,loosenthescrewandthentakeitout.
►Fig.9: 1. Groove 2. Hook 3. Screw
OPERATION
Testing the safety system
WARNING: Make sure all safety systems are
in working order before operation. Failure to do
so may cause personal injuries.
►Fig.10: 1.Trigger-lockbutton2. Switch trigger
3. Contact element 4. Sub magazine
Testsafetysystemsforpossiblefaultbeforeoperation
asfollows.
1. Unloadstaplesfromthetoolandkeepthesub
magazine opened.
2. Install the battery cartridge.
3. Only pull the switch trigger without touching the
contact element against the material.
4. Only touch the contact element against the mate-
rial without pulling the switch trigger.
Ifthetooloperatesinthecaseof3and4above,the
safetysystemsarefaulty.Stopusingthetoolimmedi-
ately and ask your local service center.
Driving staples
WARNING: Continue to place the contact
element rmly on the material until the staple is
driven completely.Unintentionalringmaycause
personalinjuries.
►Fig.11: 1. Switch trigger 2. Contact element 3. Front
part 4. Rear part
Youcanoperatethetoolineitherwayof“single
sequentialactuation”or“contactactuation”.
Single sequential actuation:
Inthismode,youcandriveonestaplebyonesequen-
tial operation.
1. Placeatthecontactelementonthematerial.
2. Holdbothofthefrontpartandtherearpartofthe
toolrmlyagainstthematerial.
3. Pulltheswitchtriggerfullytodrivethestaples.
4. Releaseyourngerfromtheswitchtriggerbefore
movethecontactelementfromthematerial.
Contact actuation:
Inthismode,youcandrivestaplessequentially.
1. Pulltheswitchtrigger.
2. Withtheswitchtriggerpulled,placeatthecon-
tact element on the material to drive the staples.
3. Movethetooltothenextareaandplaceatthe
contact element on the material again.
NOTE:Thegrooveindicatesthepointthatstapleis
driven.
►Fig.12: 1. Groove
Iftheheadofthestapleremainsabovetheworkpiece
surface,drivethestaplewhileholdingthestaplerhead
rmlyagainsttheworkpiece.
►Fig.13
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita ST113D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita ST113D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 11,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info