Manual Makita SP6000J1X (page 10 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

711055

Zoom out

Zoom in

1/68

along the full length with a stroke. The edge of the

splinterguard corresponds to the cutting edge.

When bevel cutting with the guide rail, slide the slide lever

on the tool base so that the tool does not fall down on its

side.

Move the slide lever on the tool base in the direction of

arrow so that it engages the undercut groove in the guide

rail.

Rip fence (guide rule) (Optional

accessory) (Fig. 26)

The handy rip fence allows you to do extra-accurate

straight cuts. Simply slide the rip fence up snugly against

the side of the workpiece and secure it in position with the

screws on the front and the back of the base. It also

makes repeated cuts of uniform width possible.

Overturning the rip fence (guide rule) also works as a sub

base for the tool.

Plunge cutting (Cutting-out) (Fig. 27)

WARNING:

• To avoid a kickback, be sure to observe the following

instructions.

When using the tool without guide rail

Place the tool on the workpiece with the rear edge of tool

base against a fixed stop or equivalent which is devised

by an operator.

When using the tool with guide rail

Place the tool on the guide rail with the rear edge of tool

base against a fixed stop or equivalent which is clamped

on the guide rail.

Hold the tool firmly with one hand on the front grip and the

other on the tool handle. Then push in the lock-off button

and turn the tool on and wait until the blade attains full

speed. Now press down the saw head slowly to the preset

depth of cut and simply move the tool forward to the

desired plunge position.

NOTE:

• The markings on the side of the blade guard show the

front and rear cutting points of the saw blade (A for

diameter 160 mm and B for diame-ter 165 mm) at the

maximum cutting depth and using the guide rail.

(Fig. 28)

Guide device (accessories)

Use of the miter gauge (accessory) allows exact miter

cuts with angles and fitting works.

Use of the clamp (accessory) ensures firm hold of

workpiece on the table.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Clean out the guard to ensure there is no

accumulated sawdust which may impede the

operation of the guarding system. A dirty guarding

system may limit the proper operation which could

result in serious personal injury. The most effective way

to accomplish this cleaning is with compressed air. If

the dust is being blown out of the guard, be sure

the proper eye and breathing protection is used.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Adjusting for accuracy of 90° and 45° cut

(vertical and 45° cut) (Fig. 29 & 30)

This adjustment has been made at the factory. But if it is

off, adjust the adjusting screws with a hex wrench while

inspecting 90° or 45° the blade with the base using a

triangular rule or square rule, etc.

NOTE:

• Adjusting for accuracy of 22.5°, 48° and -1° cut cannot

be performed.

Replacing carbon brushes (Fig. 31 & 32)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep the

carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones

and secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Saw blades

• Guide rail

• Rip fence (Guide rule)

• Miter gauge

•Clamp

• Hex wrench

• Sheet set for guide rail

• Rubber sheet set for guide rail

• Position sheet set for guide rail

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN62841:

Sound pressure level (L

): 92 dB (A)

Sound power level (L

): 103 dB (A)

Uncertainty (K): 3 dB (A)

ENG907-1

• The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita SP6000J1X in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita SP6000J1X Manual

Product: