383790
7
Zoom out
Zoom in
Previous page
1/64
Next page
7
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Intended use
ENE067-1
The tool is specially intended for performing plunge cuts.
In addition, lengthways and crossways straight cuts and
mitre cuts with angles in wood can also be performed
while in firm contact with the workpiece.
If the tool is equipped with the special saw blade for
aluminium, the tool can be used for sawing aluminium.
Power supply
ENF002-1
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
SPECIFIC SAFETY RULES GEB031-1
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to
circular saw safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal injury.
Danger:
1. Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw,
they cannot be cut by the blade.
2. Do not reach underneath the workpiece or tool
base. The guard cannot protect you from the blade
below the workpiece. Do not attempt to remove cut
material when blade is moving.
CAUTION: Blades coast after turn off. Wait until blade
stops before grasping cut material.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
A typical illustration of proper hand support,
workpiece support, and supply cord routing (if
applicable). (Fig. 1)
1. Clamping screw
2. Blade lower limit stopper
3. Quick stop button
4. Clamping screws
5. Tool base
6. Positive stopper
7. Lever
8. Bevel angle shifting lever
9. Base
10. Cutting line
11. Lock-off button
12. Switch trigger
13. Speed adjusting dial
14. Hex wrench
15. Locking lever
16. Shaft lock
17. Hex bolt
18. Outer flange
19. Saw blade
20. Inner flange
21. Vacuum cleaner
22. Dust port
23. Adjusting screws
24. Slide lever
25. Rip fence (Guide rule)
26. Rear edge of tool base
27. Fixed stop
28. Adjusting screw for 90°
29. Adjusting screw for 45°
30. Limit mark
31. Screwdriver
32. Brush holder cap
Model SP6000
Blade diameter 165 mm
Max. cutting depth
at 90° 56 mm
at 45° 40 mm
at 48° 38 mm
No load speed (min
-1
) 2,000 - 5,200
Overall length 341 mm
Net weight 4.1 kg
Safety class /II
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita sp 6000 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita sp 6000 k in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info