Manual Makita sp 6000 k 1x (page 10 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian)

383806

Zoom out

Zoom in

1/64

Speed adjusting dial (Fig. 17)

The tool speed can be infinitely adjusted between 2,000

and 5,200 rotations per minute by turning the adjusting

dial. Higher speed is obtained when the dial is turned in

the direction of number 6; lower speed is obtained when it

is turned in the direction of number 1.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed may

differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

CAUTION:

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

• The speed adjusting dial is not for using low speed

rated saw blades but for obtaining a speed which is

suitable to material of workpiece. Use only saw blades

which are rated for at least 5,200 min

-1

The tools equipped with electronic function are easy to

operate because of the following features.

Overload protector

When the tool is overloaded and current flows above a

certain level, the tool automatically stops to protect motor.

Constant speed control

Electronic speed control for obtaining constant speed.

Possible to get fine finish, because the rotating speed is

kept constant even under load condition.

Soft start feature

Soft start because of suppressed starting shock.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Hex wrench storage (Fig. 18)

Hex wrench is stored on the tool. To remove hex wrench,

just pull it out.

To install hex wrench, place it on the grip and insert it as

far as it will go.

Removing or installing saw blade

CAUTION:

• Do not use saw blades which do not comply with the

characteristics specified in these instructions.

• Use only saw blades which are rated for at least

5,200 min

-1

• Be sure the blade is installed with teeth pointing up at

the front of the tool.

• Use only the Makita wrench to install or remove the

blade.

To remove the blade, push in the lock-off button to unlock

the upper limit stopper.

(Fig. 19)

Turn the locking lever to lock the saw head for replacing a

blade.

(Fig. 20)

With the lock-off button depressed and the locking lever

turned, lower the handle so that the lock pin fits in the

groove formed by the locking lever and the depth guide

with scale plate. Make sure that the lock pin fits in the

groove.

Press the shaft lock fully so that the blade cannot revolve

and use the wrench to loosen the hex bolt

counterclockwise. Then remove the hex bolt, outer flange

and blade.

(Fig. 21)

To install the blade, follow the removal procedure in

reverse. BE SURE TO TIGHTEN THE HEX BOLT

CLOCKWISE SECURELY.

(Fig. 22)

Connecting a vacuum cleaner (Fig. 23)

When you wish to perform clean cutting operation,

connect a Makita vacuum cleaner to your tool. Connect a

hose of the vacuum cleaner to the dust port as shown in

the figure.

OPERATION

Section cutting (ordinary sawing) (Fig. 24)

CAUTION:

• Be sure to move the tool forward in a straight line

gently. Forcing or twisting the tool will result in

overheating the motor and dangerous kickback,

possibly causing severe injury.

• Never approach any part of your body under the tool

base when section cutting, especially at starting. Doing

so may cause serious personal injuries. The blade is

exposed under the tool base.

Hold the tool firmly. The tool is provided with both a front

grip and rear handle. Use both to best grasp the tool. If

both hands are holding saw, they cannot be cut by the

blade. Set the front of base on the workpiece to be cut

without the blade making any contact. Then push in the

lock-off button and turn the tool on and wait until the blade

attains full speed. Now press down the saw head slowly to

the preset depth of cut and simply move the tool forward

over the workpiece surface, keeping it flat and advancing

smoothly until the sawing is completed.

To get clean cuts, keep your sawing line straight and your

speed of advance uniform. If the cut fails to properly follow

your intended cut line, do not attempt to turn or force the

tool back to the cut line. Doing so may bind the blade and

lead to dangerous kickback and possible serious injury.

Release switch, wait for blade to stop and then withdraw

tool. Realign tool on new cut line, and start cut again.

Attempt to avoid positioning which exposes operator to

chips and wood dust being ejected from saw. Use eye

protection to help avoid injury.

Number min

-1

12,000

22,200

33,100

44,000

54,900

65,200

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita sp 6000 k 1x in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 2,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita sp 6000 k 1x Manual

Product: