Manual Makita SG 1250 (page 8 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian)

448645

Zoom out

Zoom in

1/52

Front handle (Fig. 10 & 11)

1. The angle of installation of the front handle is

changeable.

• To change its position, loosen the two bolts on

both sides of the front handle with the hex wrench

and move the front handle to your desired position.

NOTE:

• When the handle cannot be moved easily, loosen the

bolts furthermore.

• To secure the handle, tighten the two bolts firmly.

2. The front handle can be shifted sideways.

• To shift it, loosen and remove the two bolts on both

sides of the front handle.

• Remove the cam and install it on the opposite side

as shown in the figure.

• Insert the longer bolt to the hole in the handle on

the side close to the installed cam and the shorter

bolt on the opposite side.

• Then tighten the two bolts firmly.

Connecting to vacuum cleaner (Fig. 12)

When you wish to perform cleaner operation, connect a

vacuum cleaner to your tool. Connect a hose of vacuum

cleaner to the dust nozzle.

NOTE:

• The dust nozzle can be rotated freely so that you can

use it at any angle according to your operation.

Hex wrench storage (Fig. 13)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

CAUTION:

• Be sure to pull the tool when cutting a workpiece.

• Use this tool for straight line cutting only. Cutting curves

can cause stress cracks or fragmentation of the dia-

mond wheel resulting in possible injury to persons in

the vicinity.

• After operation, always switch off the tool and wait until

the wheel has come to a complete stop before putting

the tool down.

• Always use the front grip and firmly hold the tool by

both front grip and main handle during operations.

Adjust the front handle to appropriate position for your

work by referring to the “Front handle” in the section

“ASSEMBLY”.

Hold the tool firmly with both hands. First keep the wheel

without making any contact with a workpiece to be cut.

Then turn the tool on and wait until the wheel attains full

speed.

The cut is made by pulling the tool toward you (not by

pushing away from you). Align the notch on the base with

your cutting line, push down the front handle gently until it

stops and then pull the tool slowly to perform a cut.

(Fig. 14)

Switch off the tool in the position posed when finishing a

cut. Raise the tool after the wheel comes to a complete

stop.

Remove the remaining portion between the two blade

passage by other appropriate tools.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed. (Fig. 15)

Dressing diamond wheel

If the cutting action of the diamond wheel begins to

diminish, use an old discarded coarse grit bench grinder

wheel or concrete block to dress the diamond wheel. To

do this, tightly secure the bench grinder wheel or con-

crete block and cut in it.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by Mak-

ita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Diamond wheels

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 102 dB (A)

Sound power level (L

): 113 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: concrete cutting

Vibration emission (a

): 4.0 m/s

Uncertainty (K): 1.5 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita SG 1250 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 1,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita SG 1250

Makita SG 1250 User Manual - English, Dutch - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita SG 1250 Manual

Product: