691883

Makita SD100D Manual

8
Zoom out
Zoom in
Previous page
1/60
Next page
8 ENGLISH
Type of saw blade Max. cutting depth
For drywall 30 mm
For wood 15 mm
LED light
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keeps on lighting while the switch trigger is being pulled.
Thelampgoesoutapproximately10secondsafter
releasing the trigger.
►Fig.6: 1. Lamp
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing the dust collector
CAUTION: Never operate the tool without the
dust collector. Dust may come into your eyes and
causeeyeinjury.
Toremovethedustcollector,holdthetoolhandleand
pull back the tabs on the tool. Be sure to pull the tabs on
the both sides at the same time.
►Fig.7: 1.Tab
When installing, align the dust collector's edge with the
groove on the base.
►Fig.8: 1. Groove
Replacing drywall saw blade
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and/or blade
holder.Failuretodosomaycauseinsufcienttight-
ening of the blade, resulting in a serious personal
injury.
CAUTION: Do not touch the blade or the
workpiece immediately after operation.Theymay
be extremely hot and could burn your skin.
CAUTION: Make sure that the blade is prop-
erly secured. Insufcienttighteningoftheblademay
causebladebreakageorseriouspersonalinjury.
1. Remove the dust collector.
2. Remove the bolts on the blade holder with the hex
wrench.
►Fig.9: 1. Bolts 2. Blade holder 3. Blade
3. Setanewbladeasshowninthegure.Makesure
that the curved edge of the blade points forward. Fit the
protrusion of the blade holder into the slot on the blade.
►Fig.10: 1. Slot 2.Protrudedportion(oppositeside)
4. Adjustthecuttingdepththentightenthebolts.
5. Attachthedustcollector.
Installing snap-off blade
CAUTION: Always use the snap-off blade with
designated length, width, and thickness.Aninap-
propriatelyinstalledsnap-offbladecanbebroken.A
brokenbladecanyoffandcauseapersonalinjury.
Asnap-offbladecanalsobeusedwiththistool.Use3
segments of 18 mm wide snap-off blade with 0.5 mm
thickness.Themaximumcuttingdepthis12.5mm
when cutting a drywall.
►Fig.11: 1.Threesegmentsofsnap-offblade
1. Loosentheboltsonthebladeholder.Turnthe
blade holder so that its protrusion faces outward.
2. Insertthesnap-offbladesothatthesharpedge
faces forward.
3. Secure the snap-off blade at the position where
theendoftherstsegmentcomestotheedgeofblade
holder as illustrated.
►Fig.12: 1. Blade holder 2.Endoftherstsegment
of snap-off blade 3.Allowablecuttinglength
Attaching blade cap
CAUTION: Always attach the blade cap when
tool is not used.Abareblademaycausepersonal
injuryordamagetothebladeitself.
Passthebladecapthroughthebladeuntilthehook
catches the base cover. Note the direction of the blade
cap when attaching; the wider hook comes front side.
When removing the blade cap, lift it while pinching the
both sides.
►Fig.13: 1. Blade cap 2. Hook
During operation, insert the blade cap to the hook on
the base as illustrated until it clicks.
►Fig.14: 1. Blade cap 2. Hook
Hex wrench storage
When not in use, store the hex wrench as shown in the
guretokeepitfrombeinglost.
►Fig.15: 1. Hex wrench
Connecting a vacuum cleaner
CAUTION: Attach the blade cap before con-
necting vacuum cleaner.
Connect a Makita vacuum cleaner for clean operation.
Remove the rubber cap on the dust collector and con-
nect the vacuum cleaner's hose to the nozzle of the
dust collector.
►Fig.16: 1. Dust collector 2. Rubber cap 3. Vacuum
cleaner hose
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita SD100D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita SD100D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 13,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info