448644
8
Zoom out
Zoom in
Previous page
1/16
Next page
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
kind. The battery must be placed in a well
ventilated area during charging.
ADDITIONAL SAFETY RULES FOR
TOOL
1. Be aware that this tool is always in an operat-
ing condition, because it does not have to be
plugged into an electrical outlet.
2. Hold the tool firmly.
3. Keep face/hands, etc. away from cutters and
vicinity during operation.
4. Switch off and discontinue use immediately
when the tool does not work well or abnormal
sound occurs. Have it repaired at point of
purchase or your nearest Makita Authorized
Service Center.
5. An accidentally dropped or struck tool must
be inspected carefully for breakage, cracks or
deformities.
6. Don’t charge battery cartridge anywhere near
locations where lacquer, paint, benzene, thin-
ner, gasoline, gas or the like may be.
7. Never charge battery cartridge on top of card-
board or paper, seat/floor cushions, carpet,
vinyl, etc.
8. Never charge in a dusty location where
dust/dirt accumulates.
9. Install cutters carefully in accordance with the
instruction manual.
10. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
11. Cutters that become worn, deformed, nicked
or broken not only cause a tool breakdown;
they may cause a serious accident. Replace
them right away with new ones from Makita.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge
(Fig. 1 for SC130DRA and SC160DRA)
Always switch off the tool before insertion or
removal of the battery cartridge.
To remove the battery cartridge, pull out the set
plate on the tool and grasp both sides of the
cartridge while withdrawing it from the tool.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Snap the set plate back into
place. Be sure to close the set plate fully before
using the tool.
Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
(Fig. 2 for SC190DW)
Always switch off the tool before insertion or
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
cartridge.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way until
it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to you
or someone around you.
Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
Charging (Fig. 3 for SC130DRA and SC160DRA)
Plug the fast charger into your power source. The charging light will flash in green color. Insert the battery
cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective
markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When
the battery cartridge is inserted, the charging light color will change from green to red and charging will begin.
The charging light will remain lit steadily during charging. When charging is completed, the charging light color
will change from red to green and tone will sound steadily for about 5 seconds. After charging, unplug the
charger from the power source. Refer to the table below for the charging time.
Battery type Capacity (mAh) Number of cells
Charging time
Fast charger DC1439 Fast charger DC1209
1202/1202A 2,000 10 Approx. 14 min. Approx. 14 min.
1200 1,300 10 Approx. 9 min. Approx. 9 min.
8
SC130DRA/SC160DRA/SC190DW (E) (’100. 1. 27)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita SC 190DW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita SC 190DW in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita SC 190DW

Makita SC 190DW User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info