Manual Makita SC 120DA (page 6 of 48) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

448638

Zoom out

Zoom in

1/48

ADDITIONAL SAFETY RULES FOR MACHINE

1. If the blades are deformed, damaged or cracked,

replace them with new ones immediately.

Deformed, damaged or cracked blades can

cause machine trouble, eventually leading to

serious injury.

2. Be careful when using the machine in high or

elevated locations. Parts of cut threaded rods

may fall unexpectedly, causing serious injury.

3. Keep hands away from blades and surrounding

areas.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

To remove the battery cartridge, pull out the set plate and

withdraw the battery cartridge from the machine.

To install the battery cartridge, align its tongue with the

groove in the housing and slip it into place. Snap the set

plate back into place.

Charging (Fig.2)

Plug the fast charger into your power source. The charging light will flash in green color. Insert the battery cartridge so

that its plus and minus terminals are on the same sides as their respective markings on the fast charger. The charging

light color will change from green to red and charging will begin. The charging light will remain lit steadily during

charging. When the charging light color changes from red to green and a tone sounds steadily for approx. 5 seconds,

charging is complete. Unplug the charger from the power source.

(Note: Refer to the table below for the charging time.)

CAUTION:

• If the battery cartridge is new, or has not been used for a long time, it may not accept a full charge. You can recharge

the battery cartridge fully after discharging it completely a couple of times.

• If the battery cartridge is warm, the charging light may flash in red color. Let it cool before charging.

• If the charging light flashes alternately in green and red, and a tone sounds “beep, beep, beep, .....”, a problem exists

and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery

cartridge is worn out or damaged.

• If charging two battery cartridges in succession, give the charger 15 minutes to cool down between the two.

Switching ON and OFF (Fig.3)

CAUTION:

Before inserting the battery cartridge into the machine,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To switch on, press the trigger. To switch off, release the

trigger.

Variable trigger speed control (Fig. 3)

The speed varies from 0 to maximum, depending on the

pressure applied to the trigger. The more the trigger is

pressed, the faster the machine runs.

Replacing blades (Fig.4)

Important:

Always be sure that the machine is switched off and

battery cartridge is removed before replacing the blades.

M8 blades are factory-installed on the machine. When

cutting M10 or M12 threaded rods, replace the M8 blades

with M10 or M12 blades which are available as optional

accessories. There are two types of blades for each size;

type A should be installed on the cutter head and type B

on the cutter rod. Check the type (example: M8A or M8B)

engraved on the side of the blades and install them at the

correct position.

To replace the blades, first remove the hex socket head

bolts which secure them.

Replacing stopper (Fig.5 & 6)

Important:

Always be sure that the machine is switched off and the

battery cartridge is removed before replacing the

stopper.

The stopper for M8 or M10 blades is factory-installed on

the machine. When cutting M12 threaded rods, replace

the stopper for M8 or M10 blades with the stopper for

M12 blades which is provided as standard equipment.

To replace the stopper, remove the bolt which secures it.

Install the stopper on the machine with its claw facing

forward or upward.

Cutting operation

1. To mount the threaded rod, position the stopper with

its claw facing forward as shown in Fig. 7. With the

M8 or M10 threaded rod, move the machine head to

the threaded rod either in the X direction shown in

Fig. 7-1 or in the Y direction shown in Fig. 7-2. With

the M12 threaded rod, move the machine head in

the Y direction.

2. Mount the threaded rod so that its thread engages

that on the blade A.

CAUTION:

Always mount the threaded rod correctly as shown

in Fig. 8, never as shown in Fig. 9. Serious injury

may result.

Battery cartridge

Fast charger

DC1439 DC1414

1202 or 1202A Approx. 14 min. Approx. 45 min.

1201 or 1201A Approx. 12 min. Approx. 40 min.

1200 or 1200A Approx. 9 min. Approx. 30 min.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita SC 120DA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita SC 120DA Manual

Product: