448631
9
Zoom out
Zoom in
Previous page
1/72
Next page
9
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Intended use
ENE010-1
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
ENF002-1
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
SPECIFIC SAFETY RULES GEB018-1
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to router
safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal
parts of the tool “live” and shock the operator.
2. Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it
unstable and may lead to loss of control.
3. Wear hearing protection during extended period
of operation.
4. Handle the bits very carefully.
5. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged bit
immediately.
6. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7. Hold the tool firmly with both hands.
8. Keep hands away from rotating parts.
9. Make sure the bit is not contacting the workpiece
before the switch is turned on.
10. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
1. Adjusting knob
2. Lock lever
3. Stopper pole setting nut
4. Fast-feed button
5. Adjusting bolt
6. Stopper block
7. Depth pointer
8. Stopper pole
9. Nylon nut
10. Adjusting bolt
11. Lock button
12. Switch trigger
13. Speed adjusting dial
14. Lamp
15. Shaft lock
16. Wrench
17. Workpiece
18. Bit revolving direction
19. View from the top of the tool
20. Feed direction
21. Straight guide
22. Fine adjusting screw
23. Clamping screw (B)
24. Clamping screw (A)
25. Guide holder
26. More than 15 mm
27. Wood
28. Screws
29. Movable
30. When set to minimum opening
width
31. When set to maximum opening
width
32. Template guide
33. Lock plate
34. Bit
35. Base
36. Templet
37. Distance (X)
38. Outside diameter of the templet
guide
39. Guide holder
40. Clamping screw (C)
41. Trimmer guide
42. Guide roller
43. Dust nozzle
44. Clamping screw
45. Flat washer 6
46. Screw M6 x 135
47. Hole
48. Threaded part in the motor
bracket
49. Inside of the screw hole in the tool
base
50. Threaded part in the motor
bracket
51. Screwdriver
52. Limit mark
53. Brush holder cap
Model
RP1800/
RP1800F
RP1801/
RP1801F
RP2300FC RP2301FC
Collet chuck capacity 12 mm or 1/2”
Plunge capacity 0 - 70 mm
No load speed (min
-1
) 22,000 9,000 - 22,000
Overall length 312 mm
Net weight 6.0 kg 6.1 kg
Safety class /II
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita RP1800F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita RP1800F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info