Manual Makita PW5000CH (page 4 of 48) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598976

Zoom out

Zoom in

1/48

ENGLISH (Original instructions)

Explanation of general view

1 Shaft lock

2Cover

3 Slide switch

4 Speed adjusting dial

5Lever

6Close

7 Open

8 Abrasive disc

9Pad

10 Spindle

11 Exhaust vent

12 Inhalation vent

SPECIFICATION

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE057-1

Intended use

The tool is intended for surface work with natural stone.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future reference.

GEB052-3

STONE POLISHER SAFETY WARNINGS

Safety Warnings Common for Polishing Operation:

1. This power tool is intended to function as a pol-

isher. Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

serious injury.

2. Operations such as grinding, sanding, wire

brushing or cutting-off are not recommended to

be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. The arbour size of backing pads or any other

accessory must properly fit the spindle of the

power tool. Accessories with arbour holes that do

not match the mounting hardware of the power tool

will run out of balance, vibrate excessively and may

cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as backing pad

for cracks. If power tool or accessory is dropped,

inspect for damage or install an undamaged

accessory. After inspecting and installing an

accessory, position yourself and bystanders

away from the plane of the rotating accessory

and run the power tool at maximum no-load

speed for one minute.

Damaged accessories will

normally break apart during this test time.

8. Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by vari-

ous operations. The dust mask or respirator must be

capable of filtrating particles generated by your oper-

ation. Prolonged exposure to high intensity noise

may cause hearing loss.

9. Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of work-

piece or of a broken accessory may fly away and

cause injury beyond immediate area of operation.

10. Hold the power tool by insulated gripping sur-

faces only, when performing an operation where

the cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a

“live” wire may make exposed metal parts of the

power tool “live” and could give the operator an elec-

tric shock.

11. Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

Model PW5000C/PW5000CH

Spindle thread M14

Pad diameter Max. 125 mm

Rated speed (n) /

No load speed (n

)

2,000 – 4,400 min

–1

Overall length 313 mm

Net weight 2.3 kg

Safety class /II

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita PW5000CH in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita PW5000CH Manual

Product: