Manual Makita PV 7000 (page 6 of 20) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

78700

Zoom out

Zoom in

1/20

Speed adjusting dial (Fig. 4)

The rotating speed can be changed by turning the speed

adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the

direction of number 5. And lower speed is obtained when

it is turned in the direction of number 1. Refer to the table

below for the relationship between the number settings

on the dial and the approximate rotating speed.

CAUTION:

• If the tool is operated continuously at low speeds

(speed adjusting dial: 1 – 3), the motor will get over-

loaded and heated up.

• The speed adjusting dial can be turned only as far as 5

and back to 1. Do not force it past 5 or 1, or the speed

adjusting function may no longer work.

The tools equipped with electronic function are easy to

operate because of the following features.

• Constant speed control Electronic speed control for

obtaining constant speed. Possible to get fine finish,

because the rotating speed is kept constant even under

load condition.

• Soft start feature Safety and soft start because of sup-

pressed starting shock.

High-Low speed setting button (Fig. 3 & 5)

The tool speed can be changed instantly while the tool is

running. Depress the “ I ” position for lowest speed and

depress “ II ” position for a given number setting. The tool

speed cannot be changed when the button is in “ I ” posi-

tion, even if you turn the speed adjusting dial. When you

turn the speed adjusting dial, always be sure that the but-

ton is depressed in “ II ” position.

FOR USE AS A POLISHER

Installing or removing pad (Fig. 6)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the pad.

Hold the spindle with the wrench so that it cannot revolve.

Then screw the pad onto the spindle all the way. (The

pad can be used to install the optional sponge pad.)

To remove the pad, follow the installation procedure in

reverse.

Installing or removing sponge pad (Fig. 7)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the sponge pad.

To install the sponge pad, first remove all dirt or foreign

matter from the pad. Install the sponge pad to the pad.

To remove the pad, pull off it from the pad slowly.

Installing or removing the wool bonnet

(Fig. 8, 9 & 10)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the wool bonnet.

Mount the rubber pad onto the spindle. Screw the lock

nut onto the spindle. Hold the spindle firmly with the

wrench and tighten the lock nut using the lock nut

wrench. Fit the wool bonnet over the rubber pad. Tie a

bow knot and tuck the knot and any loose strings

between the wool bonnet and the rubber pad.

To remove the wool bonnet, follow the installation proce-

dure in reverse.

Polishing operation by sponge pad/wool

bonnet (Fig. 11 & 12)

CAUTION:

• Always wear safety glasses or a face shield during

operation.

• Apply slight pressure only. Excessive pressure will

result in poor performance and premature wear to the

sponge pad/wool bonnet.

When polishing, keep the sponge pad/wool bonnet at an

angle of about 15° to the workpiece surface.

FOR USE AS A SANDER

Installing or removing abrasive disc

(Fig. 13 & 14)

CAUTION:

Always be sure that the tool is switched off and

unplugged before installing or removing the abrasive

disc.

Mount the rubber pad onto the spindle. Fit the abrasive

disc on over the rubber pad and screw the lock nut onto

the spindle. Hold the spindle firmly with the wrench and

tighten the lock nut using the lock nut wrench.

To remove the abrasive disc, follow the installation proce-

dure in reverse.

NOTE:

The rubber pad, abrasive disc, lock nut and lock nut

wrench are optional accessories.

Sanding operation (Fig. 15)

CAUTION:

• Always wear safety glasses or a face shield during

operation.

• Apply slight pressure only. Excessive pressure will

result in poor performance and premature wear to the

abrasive disc.

• Never run the tool without the abrasive disc. You may

seriously damage the pad.

Keep the abrasive disc at an angle of about 15° to the

workpiece surface.

Number min

-1

(R.P.M.)

1–2 600–800

2–3 800–1,300

3–4 1,300–1,800

4–5 1,800–2,000

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita PV 7000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita PV 7000 Manual

Product: