Manual Makita PT354D (page 6 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691774

Zoom out

Zoom in

1/64

6 ENGLISH

Do not use this nailer for fastening electrical

cables. Itisnotdesignedforelectriccableinstalla-

tionandmaydamagetheinsulationofelectriccables

therebycausingelectricshockorrehazards.

7. Always wear safety glasses to protect your

eyes from dust or fastener injury.

WARNING: It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

Keep hands and feet away from the ejection port area.

9. Follow instruction for lubricating and chang-

ing accessories.

10. Always remove the battery cartridge before

loading the fasteners, adjustment, inspection,

maintenance or after operation is over.

11.

Make sure no one is nearby before operation. Never

attempt to drive fasteners from both the inside and

outside of wall at the same time. Fasteners may rip

through and/or y off, presenting a grave danger.

12. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

when working in high locations.

13. Never use fastener driving tools marked with

the symbol "Do not use on scaffoldings, lad-

ders" for specic application for example:

•

when changing one driving location to another

involvestheuseofscaffoldings,stairs,ladders,

orladderalikeconstructions,e.g.rooflaths;

• closingboxesorcrates;

• ttingtransportationsafetysystemse.g.on

vehicles and wagons.

14. Check walls, ceilings, oors, roong and

the like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused by

stapling into live wires, conduits or gas pipes.

15.

Use only fasteners specied in this manual. The use of

any other fasteners may cause malfunction of the tool.

16. Do not tamper with the tool or attempt to use it

for other than driving fasteners.

17. Do not operate the tool without fasteners. It

shortens the service life of the tool.

18.

Stop driving operations immediately if you notice

something wrong or out of the ordinary with the tool.

19.

Never fasten into any materials which may allow the

fastener to puncture and y through as a projectile.

20. Never actuate the switch trigger and contact

element at the same time until you are pre-

pared to fasten workpieces. Allow the work-

piece to depress the contact element. Never

defeat its purpose by securing the contact

element back or by depressing it by hand.

21.

Never tamper with the contact element. Check the

contact element frequently for proper operations.

22. Always remove fasteners from the tool when

not in use.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with

product (gained from repeated use) replace strict adher-

ence to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this instruc-

tion manual may cause serious personal injury.

Important safety instructions for

battery cartridge

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2)

Avoid storing battery cartridge in a container

with other metal objects such as nails, coins, etc.

(3)

Do not expose battery cartridge to water or rain.

A battery short can cause a large current ow, over-

heating, possible burns and even a breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

Forcommercialtransportse.g.bythirdparties,

forwardingagents,specialrequirementonpack-

agingandlabelingmustbeobserved.

Forpreparationoftheitembeingshipped,consult-

inganexpertforhazardousmaterialisrequired.

Pleasealsoobservepossiblymoredetailed

national regulations.

Tapeormaskoffopencontactsandpackupthe

batteryinsuchamannerthatitcannotmove

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Useofnon-genuineMakitabatteries,orbatteriesthat

havebeenaltered,mayresultinthebatterybursting

causingres,personalinjuryanddamage.Itwillalso

voidtheMakitawarrantyfortheMakitatoolandcharger.

Tips for maintaining maximum

battery life

Charge the battery cartridge before completely dis-

charged. Always stop tool operation and charge the

battery cartridge when you notice less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita PT354D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 12,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita PT354D Manual

Product: