Manual Makita PJ7000 (page 7 of 48) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598964

Zoom out

Zoom in

1/48

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

Adjusting the depth of groove (Fig. 1)

6 grooving depths can be preset according to the size of biscuit to be used.

Refer to the table below for the correspondence between the sizes marked on the stopper and the biscuit size. Fine

adjustments to the grooving depth can be made by turning the adjusting screw after loosening the hex nut. This may

become necessary after the blade has been resharpened a few times.

* With the rubber spikes removed.

012681

Angle guide (Fig. 2 & 3)

The angle guide height can be moved up and down to

adjust the position of the blade in relation to the top of the

workpiece.

To adjust the angle guide height, loosen the lock lever

down and rotate the knob until the pointer points to the

desired scale graduation marked on the angle guide.

Then tighten the lock lever up to secure the angle guide.

The scale on the angle guide indicates the distance from

the top of the workpiece to the center of the blade thick-

ness.

The angle guide is removable from the fence according

to the need of your work. To remove the angle guide,

loosen the lock lever and turn the knob clockwise until it

comes out of the upper end of the fence.

Fence (Fig. 4 & 5)

NOTE:

• Remove the angle guide according to the need of your

work when using the tool with the angle of the fence

adjusted to other than 0°. When you need to use the

angle guide under the above condition, be sure to

adjust the depth of groove to get a proper depth.

The angle of the fence can be adjusted between 0° and

90° (positive stops at 0°, 45° and 90°). To adjust the

angle, loosen the lock lever and tilt the fence until the

pointer points to the desired graduation on the angle

scale. Then tighten the lock lever to secure the fence.

When the fence is set at 90°, both the distance from the

center of the blade thickness to the fence and the dis-

tance from the center of the blade thickness to the bot-

tom of the blade cover are 10 mm.

Set plate (Fig. 6 & 7)

Use the set plate as shown in Fig. 6 & 7 when cutting

slots in thin workpieces.

Switch action (Fig. 8)

CAUTION:

• Before plugging in the tool, always check to see that

the slide switch actuates properly and returns to the

“OFF” position when the rear of the slide switch is

depressed.

• Switch can be locked in “ON” position for ease of operator

comfort during extended use. Apply caution when locking

tool in “ON” position and maintain firm grasp on tool.

To start the tool, slide the slide switch toward the “I (ON)”

position. For continuous operation, press the front of the

slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing the blade (Fig. 9)

CAUTION:

• When installing the plate joiner blade, mount the inner

flange with the side marked “22” facing toward you.

To remove the blade, loosen the clamp screw and open

the blade cover. Push the shaft lock and loosen the lock

nut using the lock nut wrench. To install the blade, first

mount the inner flange.

Then mount the blade and the lock nut. Securely tighten

the lock nut using the lock nut wrench. Close the blade

cover and tighten the clamp screw to secure the blade

cover.

CAUTION:

• Use only Makita lock nut wrench provided to remove or

install the blade.

• Always check the depth of groove after replacing the

blade. Readjust it if necessary.

Dust bag (Fig. 10)

To attach the dust bag, fit it onto the dust nozzle. If the

dust bag becomes an obstacle to your work, turn the dust

nozzle to change the dust bag position.

When the dust bag is about half full, switch off and

unplug the tool. Remove the dust bag from the tool and

pull the bag’s fastener out. Empty the dust bag by tap-

ping it lightly to remove as much of the dust as possible.

NOTE:

• If you connect a Makita vacuum cleaner to your plate

joiner, more efficient and cleaner operations can be

performed.

Size on stopper 0 10 20 S D MAX

Biscuit size 0 10 20 — — —

Depth of groove 8 mm 10 mm 12.3 mm 13 mm 14.7 mm 20 mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita PJ7000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita PJ7000 Manual

Product: