691825

Makita M2300 Manual

15
Zoom out
Zoom in
Previous page
1/96
Next page
15 ENGLISH
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex bolts
on the guide fence in the order from the right side.
►Fig.40: 1. Triangular rule
Bevel angle
0° bevel angle
►Fig.41: 1.0°bevelangleadjustingbolt
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin.
Loosen the knob at the rear of the tool.
Loosenthehexnutandturnthe0°bevelangleadjust-
ing bolt on the right side of the turn base two or three
revolutions clockwise to tilt the blade to the right.
Carefully square the side of the blade with the top sur-
face of the turn base using the triangular rule, try-square,
etc.byturningthe0°bevelangleadjustingboltcoun-
terclockwise. Then tighten the hex nut to secure the 0°
bevelangleadjustingboltandtightentheknobsecurely.
Make sure that the pointer on the arm points to 0° on
the bevel scale. If it does not point to 0° on the bevel
scale, loosen the screw which secures the pointer and
move and secure the pointer plate so that the pointer
points to 0° on the bevel scale.
►Fig.42: 1. Triangular rule 2. Saw blade 3. Top sur-
face of turn base
►Fig.43: 1. Pointer
45° bevel angle
►Fig.44: 1.45°bevelangleadjustingbolt2. Pointer
Adjustthe45°bevelangleonlyafterperforming0°
bevelangleadjustment.
Toadjustleft45°bevelangle,loosentheknobandtilt
the blade to the left fully.
Make sure that the pointer on the arm points to 45° on
the bevel scale on the arm.
Ifthepointerdoesnotpointto45°,turnthe45°bevelangleadjust-
ing bolt on the left side of the arm until the pointer points to 45°.
Replacing carbon brushes
►Fig.45
Remove and check the carbon brushes regularly. Replace when
they wear down to 3 mm in length. Keep the carbon brushes
clean and free to slip in the holders. Both carbon brushes should
be replaced at the same time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
►Fig.46: 1. Brush holder cap 2. Screwdriver
After use
After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guard clean
according to the directions in the previously covered
section titled "Blade guard". Lubricate the sliding por-
tions with machine oil to prevent rust.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita M2300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita M2300 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 15,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info