Manual Makita LW1401 (page 9 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691733

Zoom out

Zoom in

1/64

9 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and unplugged before carrying out

any work on the tool.

Opening center cap type safety

guard

Country specic

Forthetoolsequippedwithcentercaptypesafetyguard,

loosentheclampingscrewrstthenraisetheguard.

►Fig.11: 1.Clampingscrew

Opening European type safety

guard

Country specic

ForthetoolsequippedwithEuropeantypesafetyguard,

loosentheclampingscrewrstthenopentheguardas

shown.

►Fig.12: 1.Clampingscrew

►Fig.13

►Fig.14

Removing or installing cut-off wheel

CAUTION: Be sure to tighten the toolless

clamp or hex bolt securely.Insufcienttightening

mayresultinsevereinjury.Whentighteningthehex

bolt,usethesocketwrenchprovidedwiththetoolto

assure proper tightening.

CAUTION: Always use only the proper inner

and outer anges which are provided with the

tool.

CAUTION: Always lower the safety guard

after replacing the wheel.

►Fig.15: 1.Innerange2. Ring 3. O-ring 4.Cut-off

wheel 5.Outerange6. Toolless clamp /

Hexbolt

For LW1400

Raise the safety guard. Turn the toolless clamp coun-

terclockwise while holding down the shaft lock. Then

removethetoollessclamp,outerangeandcut-off

wheel. When removing the cut-off wheel, do not remove

theinnerangeaswellastheringandO-ring.

►Fig.16: 1. Shaft lock 2. Toolless clamp

To install the cut-off wheel, follow the removal proce-

duresinreverse.Makesuretottheholeofcut-off

wheel to the ring and return the safety guard.

For LW1401

Raisethesafetyguard.Turnthehexboltcounterclock-

wise using a socket wrench while holding down the shaft

lock.Thenremovethehexbolt,outerangeandwheel.

►Fig.17: 1. Shaft lock 2.Hexbolt

To install the wheel, follow the removal procedures in

reverse.Makesuretottheholeofcut-offwheeltothe

ring and return the safety guard.

OPERATION

CAUTION: Proper handle pressure during

cutting and maximum cutting efciency can

be determined by the amount of sparks that is

produced while cutting. Do not force the cut

by applying excessive pressure on the handle.

Reducedcuttingefciency,prematurewheelwear,as

wellas,possibledamagetothetool,cut-offwheelor

workpiece may result.

Holdthehandlermly.Switchonthetoolandwaituntil

thewheelattainsfullspeedbeforeloweringgently

into the cut. When the wheel contacts the workpiece,

graduallybeardownonthehandletoperformthecut.

When the cut is completed, switch off the tool and wait

until the wheel has come to a complete stop before

returning the handle to the fully elevated position.

Cutting capacity

Maximum cutting capacity varies depending on the

cutting angle and workpiece shape.

Max. cutting capacity with a brand-new cut-off

wheel

Cutting angle /

Workpiece shape

90° 45°

127 mm 127 mm

115 x 130 mm

102 x 194 mm

70 x 233 mm

115 x 103 mm

119 x 119 mm 106 x 106 mm

137 x 137 x 10 mm 100 x 100 x 10 mm

Securing workpiece

CAUTION: Always place the thread holder on

the shaft threads when securing the workpiece.

Failuretodosomayresultininsufcientsecuringof

theworkpiece.Thiscouldcausetheworkpiecetobe

ejectedorcauseadangerousbreakageofthewheel.

Whilethethreadholderislifted,theviseplatecanbe

moved in and out quickly. To grip a workpiece, push the

handle until the vise plate contacts the workpiece then

return the thread holder. Turn the handle clockwise until

the workpiece is securely retained.

►Fig.18: 1. Handle 2. Thread holder 3. Vise plate

Whenthecut-offwheelhasworndownconsiderably,

placeaspacerblockbehindtheworkpieceasshown

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LW1401 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 11,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LW1401 Manual

Product: