599000

Makita LS1016F Manual

24
Zoom out
Zoom in
Previous page
1/152
Next page
24
5. Compound cutting
Compound cutting is the process in which a bevel angle
is made at the same time in which a miter angle is being
cut on a workpiece. Compound cutting can be performed
at the angle shown in the table.
009713
When performing compound cutting, refer to “Press cut-
ting”, “Slide cutting”, “Miter cutting” and “Bevel cut” expla-
nations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
miter saw with the moldings laid flat on the turn base.
There are two common types of crown moldings and one
type of cove moldings; 52/38° wall angle crown molding,
45° wall angle crown molding and 45° wall angle cove
molding. See illustrations. (Fig. 53)
There are crown and cove molding joints which are made
to fit “Inside” 90° corners ((1) and (2) in Fig. 54 & 55) and
“Outside” 90° corners ((3) and (4) in Fig. 54 & 55).
Measuring
Measure the wall length and adjust workpiece on table to cut wall contact edge to desired length. Always make sure
that cut workpiece length at the back of the workpiece is the same as wall length. Adjust cut length for angle of cut.
Always use several pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table (A) and position
the moldings on the top surface of the saw base as indicated in the table (B).
In the case of left bevel cut
Table (A)
006361
Table (B)
006362
Example:
In the case of cutting 52/38° type crown molding for position (1) in Fig. 54 & 55:
• Tilt and secure bevel angle setting to 33.9° LEFT.
• Adjust and secure miter angle setting to 31.6° RIGHT.
• Lay crown molding with its broad back (hidden) surface down on the turn base with its CEILING CONTACT EDGE
against the guide fence on the saw.
• The finished piece to be used will always be on the LEFT side of the blade after the cut has been made.
Miter angle Bevel angle
Left and Right 0° – 45° Left and Right 0° – 45°
Molding position
in Fig. 54 & 55
Bevel angle Miter angle
52/38° type 45° type 52/38° type 45° type
For inside corner
(1)
Left 33.9° Left 30°
Right 31.6° Right 35.3°
(2)
Left 31.6° Left 35.3°
For outside corner
(3)
(4) Right 31.6° Right 35.3°
Molding position
in Fig. 54 & 55
Molding edge against guide fence Finished piece
For inside corner
(1)
Ceiling contact edge should be
against guide fence.
Finished piece will be on the Left
side of blade.
(2)
Wall contact edge should be against
guide fence.
For outside corner
(3)
Finished piece will be on the Right
side of blade.
(4)
Ceiling contact edge should be
against guide fence.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita LS1016F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS1016F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info