Manual Makita LS0815FL (page 17 of 132) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598999

Zoom out

Zoom in

1/132

• Never attempt to perform a slide cut by pulling the

carriage towards you. Pulling the carriage towards

you while cutting may cause unexpected kickback

resulting in possible serious personal injury.

• Never perform the slide cut with the handle locked in

the lowered position.

• Never loosen the locking screw which secures the

carriage while the blade is rotating. A loose carriage

while cutting may cause unexpected kickback resulting

in possible in serious personal injury.

3. Miter cutting

Refer to the previously covered “Adjusting the miter

angle”.

4. Bevel cut (Fig. 37)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the

workpiece with a vise. Make sure the carriage is pulled

all the way back toward the operator. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed. Then gently lower the

handle to the fully lowered position while applying

pressure in parallel with the blade and PUSH THE

CARRIAGE TOWARD THE GUIDE FENCE TO CUT

THE WORKPIECE. When the cut is completed, switch

off the tool and WAIT UNTIL THE BLADE HAS COME

TO A COMPLETE STOP before returning the blade to

its fully elevated position.

WARNING:

• After setting the blade for a bevel cut, before

operating the tool ensure that the carriage and

blade will have free travel throughout the entire

range of the intended cut. Interruption of the carriage

or blade travel during the cutting operation may result

in kickback and serious personal injury.

• While making a bevel cut keep hands out of the

path of the blade. The angle of the blade may confuse

the operator as to the actual blade path while cutting

and contact with the blade will result in serious

personal injury.

• The blade should not be raised until it has come to

a complete stop. During a bevel cut the piece cut off

may come to rest against the blade. If the blade is

raised while it is rotating the cut-off piece maybe

ejected by the blade causing the material to fragment

which may result in serious personal injury.

NOTICE:

• When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied

perpendicularly to the turn base or if the pressure

direction is changed during a cut, the precision of the

cut will be impaired.

• Before bevel-cutting, an adjustment of sliding fence

maybe required. Refer to the section titled “Guide

fence adjustment”.

5. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter angle

is being cut on a workpiece. Compound cutting can be

performed at the angle shown in the table.

010340

When performing compound cutting, refer to “Press

cutting”, “Slide cutting”, “Miter cutting” and “Bevel cut”

explanations.

6. Cutting crown and cove moldings

Crown and cove moldings can be cut on a compound

miter saw with the moldings laid flat on the turn base.

There are two common types of crown moldings and

one type of cove moldings; 52/38° wall angle crown

molding, 45° wall angle crown molding and 45° wall

angle cove molding. See illustrations. (Fig. 38)

There are crown and cove molding joints which are

made to fit “Inside” 90° corners ((1) and (2) in Fig. A)

and “Outside” 90° corners ((3) and (4) in Fig. A).

(Fig. 39 & 40)

Measuring

Measure the wall length and adjust workpiece on table

to cut wall contact edge to desired length. Always

make sure that cut workpiece length at the back of

the workpiece is the same as wall length. Adjust cut

length for angle of cut. Always use several pieces for

test cuts to check the saw angles.

When cutting crown and cove moldings, set the bevel

angle and miter angle as indicated in the table (A) and

position the moldings on the top surface of the saw

base as indicated in the table (B).

In the case of left bevel cut

Table (A)

006361

Table (B)

006362

Example:

In the case of cutting 52/38° type crown molding for

position (1) in Fig. A:

• Tilt and secure bevel angle setting to 33.9° LEFT.

• Adjust and secure miter angle setting to 31.6°

RIGHT.

Miter angle Bevel angle

Left and Right 0° - 45° Left 0° - 45°

Molding

position in

Fig. A

Bevel angle Miter angle

52/38° type 45° type 52/38° type 45° type

For inside

corner

(1)

Left 33.9° Left 30°

Right 31.6° Right 35.3°

(2)

Left 31.6° Left 35.3°

For outside

corner

(3)

(4) Right 31.6° Right 35.3°

Molding

position in

Fig. A

Molding edge against

guide fence

Finished piece

For inside

corner

(1)

Ceiling contact edge

should be against guide

fence.

Finished piece will be on

the Left side of blade.

(2)

Wall contact edge should

be against guide fence.

For outside

corner

(3)

Finished piece will be on

the Right side of blade.

(4)

Ceiling contact edge

should be against guide

fence.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS0815FL in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 4,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS0815FL Manual

Product: