Manual Makita LS 1216L (page 24 of 160) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448603

Zoom out

Zoom in

1/160

Table (B)

Example:

In the case of cutting 52/38° type crown molding for position (1) in Fig. 47 & 48:

• Tilt and secure bevel angle setting to 33.9° RIGHT.

• Adjust and secure miter angle setting to 31.6° RIGHT.

• Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will always be on the RIGHT side of the blade after the cut has been made.

Crown molding stoppers (optional accessories) allow easier cuts of crown molding without tilting the saw blade. Install

them on the base as shown in the figures. (Fig. 49 & 50)

Fig. 49: At right 45° miter angle

Fig. 50: At left 45° miter angle

Position crown molding with its WALL CONTACT EDGE against the guide fence and its CEILING CONTACT EDGE

against the crown molding stoppers as shown in the figure (Fig. 51). Adjust the crown molding stoppers according to

the size of the crown molding. Tighten the screws to secure the crown molding stoppers. Refer to the table (C) for the

miter angle.

Table (C)

7. Cutting aluminum extrusion

When securing aluminum extrusions, use spacer blocks

or pieces of scrap as shown in Fig. 52 to prevent defor-

mation of the aluminum. Use a cutting lubricant when

cutting the aluminum extrusion to prevent build-up of the

aluminum material on the blade.

WARNING:

• Never attempt to cut thick or round aluminum

extrusions. Thick or round aluminum extrusions can

be difficult to secure and may work loose during the

cutting operation which may result in loss of control and

serious personal injury.

8. Wood facing (Fig. 53)

Use of wood facing helps to assure splinter-free cuts in

workpieces. Attach a wood facing to the guide fence

using the holes in the guide fence and 6 mm screws.

See the figure concerning the dimensions for a sug-

gested wood facing.

CAUTION:

• Use straight wood of even thickness as the wood fac-

ing.

• In order to completely cut through workpieces with a

height of 102 mm to 120 mm a wood facing should be

used on the guide fence. The wood facing will space

the workpiece away from the fence allowing the blade

to complete a deeper cut.

Example:

When cutting workpieces 115 mm and 120 mm high, use

a wood facing with the following thickness.

WARNING:

• Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the

screw heads are below the surface of the wood fac-

ing so that they will not interfere with the position-

ing of the material being cut. Misalignment of the

material being cut can cause unexpected movement

during the cutting operation which may result in a loss

of control and serious personal injury.

NOTICE:

• When the wood facing is attached, do not turn the turn

base with the handle lowered. The blade and/or the

wood facing will be damaged.

Molding position

in Fig. 47 & 48

Molding edge against guide fence Finished piece

For inside corner

(1)

Wall contact edge should be against

guide fence.

Finished piece will be on the Right

side of blade.

(2)

Ceiling contact edge should be

against guide fence.

For outside corner

(3)

Finished piece will be on the Left

side of blade.

(4)

Wall contact edge should be against

guide fence.

Molding position

in Fig. 47 & 48

Miter angle Finished piece

For inside corner

(1) Right 45° Save the right side of blade

(2)

Left 45°

Save the left side of blade

For outside corner

(3) Save the right side of blade

(4) Right 45° Save the left side of blade

Miter angle

Thickness of wood facing

115 mm 120 mm

0° 35 mm 60 mm

Left and Right 45° 30 mm 45 mm

Left and Right 52° 25 mm 35 mm

Right 60° 25 mm 35 mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS 1216L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS 1216L Manual

Product: