Manual Makita LS 1016 (page 23 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448591

Zoom out

Zoom in

1/128

2) 45° bevel angle (Fig. 60)

Adjust the 45° bevel angle only after performing 0°

bevel angle adjustment. To adjust left 45° bevel

angle, loosen the lever and tilt the blade to the left

fully. Make sure that the pointer on the arm holder

points to 45° on the bevel scale on the arm. If the

pointer does not point to 45°, turn the left 45° bevel

angle adjusting bolt on the side of the arm until the

pointer points to 45°.

To adjust right 45° bevel angle, perform the same

procedure described above.

Adjusting the position of laser line (Fig. 61 & 62)

For model LS1016L only

WARNING:

• As the tool is plugged when adjusting the position of

laser line, take a full caution especially at switch action.

Pulling the switch trigger accidentally cause an acci-

dental start of the tool and personal injury.

CAUTION:

• Never look into the laser beam directly. Direct laser

beam causes damage to your eyes.

• LASER RADIATION

Do not stare into beam.

• Never apply a blow or impact to the tool. A blow or

impact causes the incorrect position of laser line, dam-

age to the laser beam emitting part or a short life of the

tool.

When adjusting the laser line appears on the left side

of the saw blade

1 Screw to change the movable range of the adjusting

screw

2 Adjusting screw

3 Hex wrench

4 Laser line

5 Saw blade

When adjusting the laser line appears on the

right side of the saw blade

1 Adjusting screw

2 Saw blade

3 Laser line

For both adjustments, do as follows.

1. Make sure that the tool is unplugged.

2. Draw the cutting line on the workpiece and place it

on the turn table. At this time, do not secure the

workpiece with a vise or similar securing device.

3. Lower the blade by lowering the handle and just

check to see where the cutting line and the position

of the saw blade is. (Decide which position to cut on

the line of cut.)

4. After decision the position to be cut, return the han-

dle to the original position. Secure the workpiece

with the vertical vise without shifting the workpiece

from the pre-checked position.

5. Plug the tool and turn on the laser switch.

6. Adjust the position of laser line as follows.

The position of laser line can be changed as the movable

range of the adjusting screw for the laser is changed by

turning two screws with a hex wrench. (The movable

range of laser line is factory adjusted within 1 mm from

the side surface of blade.)

To shift the laser line movable range further away from

the side surface of blade, turn the two screws counter-

clockwise after loosening the adjusting screw. Turn these

two screws clockwise to shift it closer to the side surface

of the blade after loosening the adjusting screw.

Refer to the section titled “Laser beam action” and adjust

the adjusting screw so that the cutting line on your work-

piece is aligned with the laser line.

NOTE:

• Check the position of laser line regularly for accuracy.

• Have the tool repaired by Makita authorized service

center for any failure on the laser unit.

Cleaning of the lens for the laser light

(Fig. 63 & 64)

For model LS1016L only

If the lens for the laser light becomes dirty, or sawdust

adheres to it in such a way that the laser line is no longer

easily visible, unplug the saw and remove and clean the

lens for the laser light carefully with a damp, soft cloth.

Do not use solvents or any petroleum-based cleaners on

the lens.

To remove the lens for the laser light, remove the saw

blade before removing the lens according to the instruc-

tions in the section titled “Installing or removing saw

blade”.

Loosen but do not remove the screw which secures the

lens using a screwdriver.

Pull out the lens as shown in the figure.

NOTE:

• If the lens does not come out, loosen the screw further

and pull out the lens again without removing the screw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS 1016 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS 1016 Manual

Product: