Manual Makita LS 1013L (page 20 of 108) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448587

Zoom out

Zoom in

1/108

4. Bevel cut (Fig. 43)

Loosen the lever and tilt the saw blade to set the bevel

angle (Refer to the previously covered “Adjusting the

bevel angle”). Be sure to retighten the lever firmly to

secure the selected bevel angle safely. Secure the work-

piece with a vise. Make sure the carriage is pulled all the

way back toward the operator. Switch on the tool without

the blade making any contact and wait until the blade

attains full speed. Then gently lower the handle to the

fully lowered position while applying pressure in parallel

with the blade and PUSH THE CARRIAGE TOWARD

THE GUIDE FENCE TO CUT THE WORKPIECE. When

the cut is completed, switch off the tool and WAIT UNTIL

THE BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated position.

CAUTION:

• Always be sure that the blade will move down to bevel

direction during a bevel cut. Keep hands out of path of

saw blade.

• During a bevel cut, it may create a condition whereby

the piece cut off will come to rest against the side of the

blade. If the blade is raised while the blade is still rotat-

ing, this piece may be caught by the blade, causing

fragments to be scattered which is dangerous. The

blade should be raised ONLY after the blade has come

to a complete stop.

• When pressing down the handle, apply pressure in par-

allel with the blade. If a force is applied perpendicularly

to the turn base or if the pressure direction is changed

during a cut, the precision of the cut will be impaired.

• Always set the sub-fence to the left position when per-

forming left bevel cuts.

5. Compound cutting

Compound cutting is the process in which a bevel angle

is made at the same time in which a miter angle is being

cut on a workpiece. Compound cutting can be performed

at angle shown in the table.

At the miter angle of left 45° and bevel angle of left 45°,

workpieces up to 50 mm high and 200 mm wide can be

cut.

At the miter angle of right 45° and bevel angle of left 45°,

workpieces up to 50 mm high and 215 mm wide can be

cut.

At the miter angle of left and right 45° and bevel angle of

right 45°, workpieces up to 31 mm high and 215 mm

wide can be cut.

When performing compound cutting, refer to “Press cut-

ting”, “Slide cutting”, “Miter cutting” and “Bevel cut” expla-

nations.

6. Cutting aluminum extrusion

When securing aluminum extrusions, use spacer blocks

or pieces of scrap as shown in Fig. 44 to prevent defor-

mation of the aluminum. Use a cutting lubricant when

cutting the aluminum extrusion to prevent build-up of the

aluminum material on the blade.

CAUTION:

• Never attempt to cut thick or round aluminum extru-

sions. Thick aluminum extrusions may come loose dur-

ing operation and round aluminum extrusions cannot

be secured firmly with this tool. (Fig. 45)

7. Groove cutting (Fig. 46)

A dado type cut can be made by proceeding as follows:

Adjust the lower limit position of the blade using the

adjusting screw and the stopper arm to limit the cutting

depth of the blade. Refer to “Stopper arm” section

described previously.

After adjusting the lower limit position of the blade, cut

parallel grooves across the width of the workpiece using

a slide (push) cut as shown in the figure. Then remove

the workpiece material between the grooves with a

chisel. Do not attempt to perform this type of cut using

wide (thick) blades or with a dado blade. Possible loss of

control and injury may result.

CAUTION:

• Be sure to return the stopper arm to the original posi-

tion when performing other than groove cutting.

Carrying tool

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at right miter angle fully.

Secure the slide poles after pulling the carriage toward

you fully. Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. (Fig. 47)

Carry the tool by holding both sides of the tool base as

shown in the figure. If you remove the holders, dust bag,

etc., you can carry the tool more easily. (Fig. 48)

CAUTION:

• Always secure all moving portions before carrying the

tool.

• Stopper pin is for carrying and storage purposes only

and not for any cutting operations.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

WARNING:

• Always be sure that the blade is sharp and clean for the

best and safest performance.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle

Push the carriage toward the guide fence and tighten the

knob to secure the carriage.

Loosen the grip which secures the turn base. Turn the

turn base so that the pointer points to 0° on the miter

scale. Then turn the turn base slightly clockwise and

counterclockwise to seat the turn base in the 0° miter

notch. (Leave as it is if the pointer does not point to 0°.)

Loosen the hex bolts securing the guide fence using the

socket wrench. (Fig. 49)

Miter angle Bevel angle

Left 0°–47°,

Right 0°–45°

Left and Right 0°–45°

Right 52° Left 0°–40° and Right 0°–45°

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS 1013L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita LS 1013L

Makita LS 1013L User Manual - English, Dutch - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita LS 1013L Manual

Product: