448585
7
Zoom out
Zoom in
Previous page
1/20
Next page
7
ENGLISH
Explanation of general view
1 Auxiliary plate
2Hex bolt
3Base
4Nut
5Bolt
6Center cover
7 Socket wrench
8 Safety cover
9 Shaft lock
10 Blade case
11 Guide arm
12 Pin
13 Inner flange
14 Spindle
15 25.4 mm marking
16 Saw blade
17 Outer flange
18 Dust bag
19 Fastener
20 Dust spout
21 Switch trigger
22 Kerf board
23 Turn base
24 Depth adjusting screw
25 Screwdriver
26 Guide fence
27 Screw
28 Pointer
29 Clamp screw
30 Wing bolt
31 Vise arm
32 Workpiece
33 Holder
34 Adjusting plate
35 Knob
36 Lock lever
37 Groove
38 Cutting line
39 Fence plate
40 Bolts
41 Bolt
42 Arm
43 Screw (A)
44 Ruler
45 Screw (B)
46 Stopper pin
47 Limit mark
48 Brush holder cap
SPECIFICATIONS
Model LS0810
Blade diameter ...................................................210 mm
Max. cutting capacities (H x W)
Cross cut (90°) ......................................... 55 x 130 mm
Miter cut (45°) ............................................ 55 x 95 mm
No load speed (RPM) .............................................5,000
Dimensions (L x W x H) .................. 390 x 270 x 385 mm
Net weight .............................................................. 5.6 kg
Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
NOTE: Specifications may differ from country to coun-
try.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Wear eye protection.
2. Do not operate saw without guards in place.
3. Don’t use the tool in the presence of flammable
liquids or gases.
4. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
5. Use only flanges specified for this tool.
6. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt. Dam-
age to these parts could result in blade break-
age.
7. Make sure that the turn base is properly secured
so it will not move during operation.
8. For your safety, remove the chips, small pieces,
etc. from the table top before operation.
9. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
10. Make sure the shaft lock is released before the
switch is turned on.
11. Be sure that the blade does not contact the turn
base in the lowest position.
12. Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
13. Do not perform any operation freehand. The
workpiece must be secured firmly against the
turn base and guide fence with the vise during
all operations. Never use your hand to secure
the workpiece.
14. Keep hands out of path of saw blade. Avoid con-
tact with any coasting blade. It can still cause
severe injury.
15. Never reach around saw blade.
16. Make sure the blade is not contacting the work-
piece before the switch is turned on.
17. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
18. Wait until the blade attains full speed before cut-
ting.
19. Stop operation immediately if you notice any-
thing abnormal.
20. Do not attempt to lock the trigger in the ON posi-
tion.
21. Shut off power and wait for saw blade to stop
before servicing or adjusting tool.
22. Be alert at all times, especially during repetitive,
monotonous operations. Don’t be lulled into a
false sense of security. Blades are extremely
unforgiving.
23. Always use accessories recommended in Makita
catalog. Use of improper accessories such as
abrasive wheels may cause an injury.
24. Don’t abuse cord. Never yank cord to disconnect
it from the receptacle. Keep cord away from heat,
oil, water and sharp edges.
25. Do not use the saw to cut other than aluminum,
wood or similar materials.
26. Connect miter saws to a dust collecting device
when sawing.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita LS 0810 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita LS 0810 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita LS 0810

Makita LS 0810 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info